Front Left CV Axle for 1995-2000 Mazda Millenia - A1 CARDONE 66-8093

$123.99

Vehicles this part fits

    Part number: 66-8093
    UPC: 082617635691
    Condition: New
    Weight: 19.00 LBS
    Item Package Quantity: 1
    $123.99
    Adding to cart… The item has been added

    Have questions?

    CARDONE New CV Axle Assembly P/N:66-8093
    CARDONE New CV Axle Assembly P/N:66-8093
    $123.99
    $123.99

    A1 CARDONE 66-8093 front left CV axle for the 1995-2000 Mazda Millenia carries drive torque from the transaxle to the wheel. This new CV axle assembly has Neoprene boots with extra bellows where needed to resist ozone cracking, the leading cause of boot failure.

    • Each shaft is individually verified for straightness for vibration-free running at all speeds
    • Axle measurements are validated after assembly
    • Boot clamps are pneumatically crimped to seal the boot to the housing
    • Grease made to withstand high-temperature and high-torque demands
    • Precision-rolled splines and threads; transmission seal diameter precision-machined after heat treatment

    Quick facts

    • Part: A1 CARDONE 66-8093 CV axle
    • Also called: CV axle assembly
    • Fits: 1995-2000 Mazda Millenia
    • Position: Front left
    • Material: Steel shaft, Neoprene boots
    • Condition: New

    A clicking or snapping noise when you turn hard under power, a thump or vibration when you accelerate, or grease leaking from a torn boot can all mean the axle is wearing out. These signs alone do not prove the axle is at fault, since a broken engine mount can misalign the axle and produce a similar problem.

    Fits

    This is a direct-fit replacement for the 1995-2000 Mazda Millenia. The car has one axle at each front wheel; this listing is the front left, so the front right is ordered separately, and both sides are normally replaced together.

    Specifications

    Fit and size

    • Position: Front left
    • Quantity per application: 1
    • Shaft diameter: 27 mm (1.063 in)
    • Compressed length: 641.35 mm (25.25 in)
    • Inboard joint: splined, 30 splines
    • Outboard joint: splined, 28 splines
    • Axle nut thread: M22x1.5
    • Axle nut socket size: 32 mm (1.26 in)

    Build and materials

    • Condition: New
    • Shaft material: Steel
    • Boot material: Neoprene
    • CV joints: included
    • Axle nut: hex, included
    • ABS tone ring: included, toothed, 44 teeth
    • Country of origin: China

    In the box

    One complete CV axle with a new axle retaining nut and an instruction sheet.

    Installation notes

    • Remove and install one axle at a time.
    • Use a torque wrench on the axle nut, never an impact wrench, and torque it to the manufacturer's specification.
    • Install new transaxle seals when replacing the axle.
    • Do not let the axle hang unsupported while you work.

    Interchange: GR052560XA · GR052560XE · GR052560XF

    Product information is for general reference and may contain errors. See our Disclaimer.

    This part cross-references / interchanges with the following part numbers:

    GR052560XA, GR052560XE, GR052560XF

    Frequently Asked Questions

    Is the A1 CARDONE 66-8093 the right front left CV axle for the 1995-2000 Mazda Millenia?

    Yes. The A1 CARDONE 66-8093 is the front left CV axle for the 1995-2000 Mazda Millenia, and the front right is a separate part.

    Does the A1 CARDONE CV drive axle come with a new axle nut?

    Yes. The 66-8093 comes with a new hex axle retaining nut (M22x1.5) and an instruction sheet, since the original nut is likely worn or stripped.

    Do A1 CARDONE axles like this one include the CV joints and the ABS tone ring?

    Yes. This front left axle has its CV joints and a toothed ABS tone ring with 44 teeth, and the splined inboard and outboard joints have 30 and 28 splines.

    Why does my front left CV axle click when I turn hard?

    A click or snap when you turn hard under power can mean a worn outer joint, and grease leaking from a torn boot is another sign. A shop can confirm the cause.

    Can I use an impact wrench on the 66-8093 axle nut?

    No. Torque the nut to the manufacturer's specification with a torque wrench, and use a press tool, not a hammer, to free a stuck stub shaft.

    Reviews

    No reviews yet — be the first to review this product.

    Write a Review