Rear CV Axle for 2011-2016 Volvo S60 & More - A1 CARDONE 66-9778

$181.99

Vehicles this part fits

    Part number: 66-9778
    UPC: 884548300392
    Condition: New
    Weight: 12.80 LBS
    Item Package Quantity: 1
    $181.99
    Adding to cart… The item has been added

    Have questions?

    CARDONE New CV Axle Assembly P/N:66-9778
    CARDONE New CV Axle Assembly P/N:66-9778
    $181.99
    $181.99

    A1 CARDONE 66-9778 rear CV axle for the 2011-2016 Volvo S60 and other vehicles carries engine torque from the transaxle to the wheel. The A1 CARDONE CV axle is a complete assembly with CV joints, designed around the common reasons original axles fail, such as boot cracking.

    • Neoprene boots with additional bellows where needed to resist bellow stress and ozone cracking
    • A1 CARDONE axles have each shaft individually verified for straightness for vibration-free performance at all speeds
    • Axle measurements are validated after assembly to confirm a proper fit
    • Boot clamps are pneumatically crimped to seal the boot to the housing
    • Grease that withstands high temperature and high torque
    • Precision-rolled splines and threads for proper fit in the hub, the transmission and the axle nut

    Quick facts

    • Part: A1 CARDONE 66-9778 CV axle
    • Also called: CV axle assembly
    • Fits: 2011-2016 Volvo S60 and other vehicles
    • Position: Rear right, rear left
    • Material: Steel shaft, neoprene boots
    • Condition: New

    Clicking or snapping when you turn hard under throttle, a thump or vibration when accelerating, or grease on the chassis can mean a worn joint or a torn boot. These signs alone do not prove the axle is the problem, since a worn wheel bearing can make a similar noise. Both rear sides are normally replaced together.

    Fits

    Fitment includes the 2011-2016 Volvo S60, the 2015-2016 Volvo V60 and the 2007-2015 Volvo S80. If your car is something else, look it up in the "Vehicles it fits" section.

    Specifications

    Fit and size

    • Position: rear right, rear left
    • Quantity per application: 1
    • Shaft diameter: 25 mm (0.984 in)
    • Compressed length: 748 mm (29.449 in)
    • Splines: 26 inboard, 36 outboard
    • Axle nut: hex, M10x1.5 thread, 12.8 mm (0.504 in) socket

    Build and materials

    • Shaft material: steel
    • Boot material: neoprene
    • ABS tone ring: included, magnetic, 44 teeth
    • CV joints: included
    • Condition: new
    • Country of origin: China

    In the box

    One complete axle with CV joints, a new axle retaining nut and an instruction sheet. This listing holds one axle, for either rear side, and each application calls for one.

    Installation notes

    • Remove and install one CV axle at a time.
    • Install new transaxle seals when replacing the axle.
    • Use a press-type tool to remove the old stub shaft; never strike it with a hammer.

    Interchange: 36000156 · 36000931

    Product information is for general reference and may contain errors. See our Disclaimer.

    This part cross-references / interchanges with the following part numbers:

    36000156, 36000931

    Frequently Asked Questions

    Is this Volvo S60 CV axle for the 2011-2016 model years?

    Yes, A1 CARDONE 66-9778 is a rear CV axle for the 2011-2016 Volvo S60, and the 2015-2016 Volvo V60 is in the fitment too; other cars are in the "Vehicles it fits" section.

    Does the A1 CARDONE CV drive axle come with a new axle nut?

    Yes, the box holds the complete axle with CV joints, a new axle retaining nut and an instruction sheet; the nut is supplied because the original is likely worn or stripped.

    Does this CV axle assembly include a magnetic ABS tone ring?

    Yes. A1 CARDONE 66-9778 includes a magnetic ABS tone ring with 44 teeth, and its shaft is steel with a 25 mm diameter.

    What can a clicking noise when turning hard mean for a rear CV axle?

    Clicking or snapping on a hard turn under throttle can come from a worn outer joint, and grease on the chassis can mean a torn boot. A shop can inspect the axle to find out which.

    Can I use an impact wrench on the axle retaining nut?

    No. Use a torque wrench and tighten the retaining nut to the vehicle manufacturer's specification, never an impact wrench.

    Reviews

    No reviews yet — be the first to review this product.

    Write a Review