Rear Right Brake Caliper for 2004-2010 Toyota Sienna - A1 CARDONE 2C-2872

$142.99

Vehicles this part fits

    Part number: 2C-2872
    UPC: 884548295506
    Condition: New
    Weight: 13.50 LBS
    Item Package Quantity: 1
    $142.99
    Adding to cart… The item has been added

    Have questions?

    CARDONE New Disc Brake Caliper P/N:2C-2872
    CARDONE New Disc Brake Caliper P/N:2C-2872
    $142.99
    $142.99

    A1 CARDONE 2C-2872 rear right brake caliper for the 2004-2010 Toyota Sienna clamps the pads against the rotor to slow the vehicle. Also called a disc brake caliper, this new, direct-fit unit is zinc coated.

    • Floating design with a single steel piston
    • Cast iron body with a zinc plated finish and a rust-resistant coating
    • Pad wear sensor included
    • Every unit is 100% tested

    Quick facts

    • Part: A1 CARDONE 2C-2872 brake caliper
    • Also called: disc brake caliper
    • Fits: 2004-2010 Toyota Sienna
    • Position: Rear right
    • Material: Cast iron
    • Condition: New

    A sticking caliper can show up as the car pulling to one side under braking, uneven pad wear or a brake fluid leak at the wheel, and each of these can have other causes. As part of a brake service, look at whether the slide pins move freely and whether the brake hose is collapsed before you decide the caliper is at fault.

    Fits

    It fits the 2004-2010 Toyota Sienna, which takes one on this side. This listing is the rear right caliper; the rear left is a separate part ordered on its own, and both sides are normally replaced together.

    Specifications

    Fit and size

    • Position: rear right
    • Quantity per vehicle: 1
    • Piston diameter: 42.8 mm (1.69 in)
    • Mounting hole diameter: 0.472 in
    • Mounting type: M10x1.0
    • Bleeder thread size: M7x1.0
    • Inlet fitting type: inverted flare

    Build and materials

    • Caliper type: floating, 1 piston
    • Caliper casting material: cast iron
    • Piston material: steel
    • Finish: zinc plated, with a rust-resistant coating
    • Condition: new
    • Country of origin: Republic of Korea

    In the box

    One brake caliper with its bracket, hardware kit, abutment clips, one bleeder screw, pad wear sensor and an instruction sheet. Brake pads and mounting bolts are not included, so plan on new bolts.

    Installation notes

    • A silicone grease is used on floating caliper mounting pins.
    • Use the brake fluid the vehicle maker recommends; the type is stamped on the master cylinder reservoir lid. Use new fluid from a sealed container.

    Interchange: 4773028270

    Product information is for general reference and may contain errors. See our Disclaimer.

    This part cross-references / interchanges with the following part numbers:

    4773028270

    Frequently Asked Questions

    Does the A1 CARDONE 2C-2872 fit the rear right side of a 2004-2010 Toyota Sienna?

    Yes, A1 CARDONE 2C-2872 is the rear right caliper for the 2004-2010 Toyota Sienna. The rear left caliper is a separate part, ordered on its own.

    What comes with this A1 CARDONE brake caliper?

    It comes with a bracket, hardware kit, abutment clips, one bleeder screw, a pad wear sensor and an instruction sheet. Brake pads and mounting bolts are not included.

    How big is the piston on the A1 CARDONE caliper?

    The A1 CARDONE 2C-2872 is a floating caliper with a single steel piston. The piston diameter is 42.8 mm (1.69 in).

    Can a bad rear right brake caliper make a car pull to one side?

    It can be one cause, along with sticking slide pins or a collapsed brake hose. Have a shop check the brakes, and do not keep driving on a suspected brake fault.

    Which brake fluid goes with a new caliper like this?

    Go by the vehicle maker's recommendation: the fluid type is stamped on the master cylinder reservoir lid. Pour from a fresh, sealed container of new fluid.

    Reviews

    No reviews yet — be the first to review this product.

    Write a Review