Rear Left Brake Caliper for 2004-2010 Toyota Sienna - A1 CARDONE 2C-2873

$142.99

Vehicles this part fits

    Part number: 2C-2873
    UPC: 884548295513
    Condition: New
    Weight: 13.50 LBS
    Item Package Quantity: 1
    $142.99
    Adding to cart… The item has been added

    Have questions?

    CARDONE New Disc Brake Caliper P/N:2C-2873
    CARDONE New Disc Brake Caliper P/N:2C-2873
    $142.99
    $142.99

    A1 CARDONE 2C-2873 rear left brake caliper for the 2004-2010 Toyota Sienna clamps the brake pad against the rotor to slow the wheel. It is sold new and unloaded.

    • Zinc-plated silver finish with a rust-resistant coating
    • Every unit is 100% tested
    • Floating design with a single steel piston, 42.8 mm (1.69 in) in diameter
    • Cast iron caliper body with an inverted flare inlet fitting

    Quick facts

    • Part: A1 CARDONE 2C-2873 brake caliper
    • Also called: disc brake caliper
    • Fits: 2004-2010 Toyota Sienna
    • Position: Rear left
    • Material: Cast iron caliper body, steel piston
    • Condition: New

    Rear calipers are normally swapped as a pair, and this listing covers one. A caliper with sticky slides can show up as the car pulling to one side under braking, uneven pad wear or brake fluid around the caliper. Before buying, look the brake hose over for cracks or a collapsed section, since a restricted hose can pull the car to one side as well. If a failed caliper is the cause, this one replaces it.

    Fits

    It is a direct-fit rear left caliper for the 2004-2010 Toyota Sienna, engineered to meet or exceed O.E. performance.

    Specifications

    Fit and size

    • Position: Rear left
    • Quantity per vehicle: 1 for this side
    • Piston diameter: 42.8 mm (1.69 in)
    • Pistons: 1
    • Mounting hole diameter: 0.472 in
    • Mounting type: M10x1.0
    • Bleeder thread size: M7x1.0
    • Inlet fitting type: Inverted flare

    Build and materials

    • Caliper type: Floating
    • Caliper casting material: Cast iron
    • Piston material: Steel
    • Finish: Zinc plated, rust-resistant coating
    • Condition: New
    • Country of origin: South Korea

    In the box

    One caliper with its bracket, a hardware kit, one bleeder screw, abutment clips and an instruction sheet. This listing holds one caliper; the rear left takes one, and the rear right is a separate part. Brake pads and mounting bolts are not included, so plan on new mounting bolts, since the old ones may not be reusable.

    Installation notes

    • An instruction sheet comes with the caliper for the installation steps.
    • Use the brake fluid the vehicle maker recommends; the fluid type is stamped on the master cylinder reservoir lid, and it should come from a sealed container.
    • A silicone grease is used on floating caliper mounting pins.

    Interchange: 4775028270

    Product information is for general reference and may contain errors. See our Disclaimer.

    This part cross-references / interchanges with the following part numbers:

    4775028270

    Frequently Asked Questions

    Does this A1 CARDONE brake caliper fit the rear left of a 2004-2010 Toyota Sienna?

    Yes. A1 CARDONE 2C-2873 is a rear left caliper for the 2004-2010 Toyota Sienna. The rear right side is a separate part.

    Does the A1 CARDONE caliper come with a bracket and hardware?

    Yes. A1 CARDONE 2C-2873 comes with its bracket, a hardware kit, a bleeder screw, abutment clips and an instruction sheet. Brake pads and mounting bolts are not included.

    Is this disc brake caliper floating or fixed, and how big is the piston?

    This rear left caliper is a floating design with one steel piston, 42.8 mm (1.69 in) in diameter. The body is cast iron with a zinc-plated finish.

    What can a floating caliper with binding slide pins cause?

    Binding slides or pins can leave the car pulling to one side under braking, and brake fluid around the caliper is another sign. Have the brakes checked promptly if you notice either.

    Which grease and brake fluid go with this caliper?

    For A1 CARDONE 2C-2873, use silicone grease on the floating caliper mounting pins. Brake fluid is the type stamped on the master cylinder reservoir lid, taken from a sealed container.

    Reviews

    No reviews yet — be the first to review this product.

    Write a Review