Front Left Brake Caliper for 1968-1973 Ford Mustang & More - A1 CARDONE 2C-4013

$141.99

Vehicles this part fits

    Part number: 2C-4013
    UPC: 884548341449
    Condition: New
    Weight: 8.60 LBS
    Item Package Quantity: 1
    $141.99
    Adding to cart… The item has been added

    Have questions?

    CARDONE New Disc Brake Caliper P/N:2C-4013
    CARDONE New Disc Brake Caliper P/N:2C-4013
    $141.99
    $141.99

    A1 CARDONE 2C-4013 front left brake caliper for the 1968-1973 Ford Mustang and other vehicles clamps the brake pads against the rotor to slow the wheel. This A1 CARDONE brake caliper is a new, unloaded caliper.

    • Floating caliper with one steel piston
    • Cast iron body with zinc plating for a silver finish and a rust-resistant coating
    • Every unit is 100% tested
    • Banjo inlet fitting and a 3/8x24 bleeder screw thread

    Quick facts

    • Part: A1 CARDONE 2C-4013 brake caliper
    • Also called: disc brake caliper
    • Fits: 1968-1973 Ford Mustang and other vehicles
    • Position: Front left
    • Material: Cast iron
    • Condition: New

    A worn or sticking disc brake caliper can show up as the car pulling to one side, a brake that drags or fluid around the wheel. Those signs can have other causes, so during a brake service look over the caliper slides and pins for binding and the brake hose for a collapsed or restricted section. This listing is one caliper; the front left position takes one, the front right is a separate part, and both sides are normally replaced together.

    Fits

    This direct-fit caliper is listed for a wide range of Ford and Mercury models, including the 1968-1973 Ford Mustang, the 1968-1973 Mercury Cougar and the 1968-1971 Ford Ranchero. It is engineered to meet or exceed O.E. performance and suits commercial use as well as performance vehicles. Open the "Vehicles it fits" section to check your exact model and engine.

    Specifications

    Fit and size

    • Position: Front left
    • Quantity per application: 1
    • Piston: 1, 60.2 mm (2.37 in) diameter
    • Mounting hole diameter: 0.305 in
    • Mounting type: 3/8x24
    • Bleeder thread size: 3/8x24
    • Inlet fitting: Banjo

    Build and materials

    • Caliper type: Floating
    • Caliper body material: Cast iron
    • Piston material: Steel
    • Finish: Zinc plated, silver, with rust-resistant coating
    • Condition: New
    • Country of origin: China

    In the box

    One caliper, one instruction sheet and a hardware kit. Abutment clips, an anti-rattle spring, a bleeder screw, a mounting bolt and a pad wear sensor are included. Brake pads and the mounting bracket are not included.

    Installation notes

    • The instruction sheet in the box covers the installation steps.
    • A silicone grease is used on floating caliper mounting pins.
    • Use the brake fluid the vehicle maker recommends, from a new sealed container; the type is stamped on the master cylinder reservoir lid.

    Interchange: C80Z2B121A

    Product information is for general reference and may contain errors. See our Disclaimer.

    This part cross-references / interchanges with the following part numbers:

    C80Z2B121A

    Frequently Asked Questions

    Does this caliper fit the 1968-1973 Ford Mustang?

    Yes, A1 CARDONE 2C-4013 is listed for the 1968-1973 Ford Mustang as the front left caliper. Open the "Vehicles it fits" section to check your exact model and engine.

    Does the A1 CARDONE 2C-4013 come with a mounting bracket or brake pads?

    No. A1 CARDONE 2C-4013 comes with the caliper, a hardware kit and an instruction sheet; the brake pads and the mounting bracket are not included.

    What size is the piston in this floating caliper?

    This front left caliper has one steel piston that measures 60.2 mm (2.37 in) across.

    Which brake fluid should I use, DOT 3, DOT 4 or DOT 5?

    Use the fluid stamped on the master cylinder reservoir lid, which is the one the vehicle maker recommends, and pour it from a new sealed container.

    What grease goes on the mounting pins of a floating caliper?

    Floating caliper mounting pins take silicone grease. The instruction sheet that comes with this caliper covers the installation steps.

    Reviews

    No reviews yet — be the first to review this product.

    Write a Review