Front Right Brake Caliper for 2001-2007 Ford Escape & More - A1 CARDONE 2C-4779

$205.99

Vehicles this part fits

    Part number: 2C-4779
    UPC: 884548289703
    Condition: New
    Weight: 12.00 LBS
    Item Package Quantity: 1
    $205.99
    Adding to cart… The item has been added

    Have questions?

    CARDONE New Disc Brake Caliper P/N:2C-4779
    CARDONE New Disc Brake Caliper P/N:2C-4779
    $205.99
    $205.99

    A1 CARDONE 2C-4779 front right brake caliper for the 2001-2007 Ford Escape and other vehicles presses the brake pads against the rotor to slow the wheel. It is a new floating disc brake caliper, sold unloaded without pads.

    • Floating design with one steel piston, 59.84 mm (2.36 in) in diameter
    • Cast iron body with a banjo inlet fitting
    • Zinc-plated silver finish with a rust-resistant coating
    • Every unit is 100% tested

    Quick facts

    • Part: A1 CARDONE 2C-4779 front right brake caliper
    • Also called: disc brake caliper
    • Fits: 2001-2007 Ford Escape and other vehicles
    • Position: Front right
    • Material: Cast iron body, steel piston
    • Condition: New

    A caliper with sticking slides or pins can show up as the car pulling to one side under braking, squealing or a low pedal, and other brake parts can produce those symptoms as well. During a brake service, check the slides and pins for binding and the brake hoses for collapse before deciding on a caliper.

    Fits

    It is a direct-fit replacement for the 2001-2007 Ford Escape, the 2001-2006 Mazda Tribute and the 2005-2006 Mercury Mariner. This listing is one caliper for the front right; the front left is a separate part, and the two on the front axle are normally replaced together.

    Specifications

    Fit and size

    • Position: Front right
    • Quantity per vehicle: 1 for this position
    • Number of pistons: 1
    • Piston diameter: 59.84 mm (2.36 in)
    • Mounting hole diameter: 0.551 in
    • Mounting type: M10x1.0
    • Bleeder thread size: 3/8x24

    Build and materials

    • Caliper type: Floating
    • Casting material: Cast iron
    • Piston material: Steel
    • Finish: Zinc plated, with rust-resistant coating
    • Inlet fitting: Banjo
    • Condition: New
    • Country of origin: Vietnam

    In the box

    One caliper with its bracket, hardware kit, bleeder screw, anti-rattle spring, pad wear sensor and instruction sheet. This listing holds one caliper, and the front right takes one. Brake pads, abutment clips and mounting bolts are not included; plan on new mounting bolts.

    Installation notes

    • An instruction sheet comes with the caliper for the steps.
    • Silicone grease is used on floating caliper mounting pins.
    • Use the brake fluid the vehicle maker recommends; the type is stamped on the master cylinder reservoir lid, and it should come from a sealed container.

    Interchange: 5L8Z2B120AD · 6L8Z2B120BA · YL8Z2B120AB · ECZ13398ZD · EFY13398ZA · ZZC03398Z

    Product information is for general reference and may contain errors. See our Disclaimer.

    This part cross-references / interchanges with the following part numbers:

    5L8Z2B120AD, 6L8Z2B120BA, YL8Z2B120AB, ECZ13398ZD, EFY13398ZA, ZZC03398Z

    Frequently Asked Questions

    Is this caliper right for the 2001-2007 Ford Escape?

    Yes. A1 CARDONE 2C-4779 is the front right caliper for the 2001-2007 Ford Escape. The front left side is a separate part.

    Does the A1 CARDONE brake caliper come with a mounting bracket?

    Yes. The A1 CARDONE 2C-4779 package includes the bracket, a hardware kit, a bleeder screw, an anti-rattle spring and an instruction sheet. Mounting bolts are not included, so plan on new ones.

    Is the A1 CARDONE caliper loaded or unloaded?

    Unloaded. It comes without brake pads, though the bracket, hardware kit and pad wear sensor are included.

    Can I swap this steel piston caliper for a phenolic piston one?

    No, it is not recommended. The vehicle maker specified steel or phenolic pistons for the intended use, and this caliper has a steel piston, so follow the vehicle maker's recommendation.

    What grease and brake fluid go with this floating caliper?

    Silicone grease is used on floating caliper mounting pins. For brake fluid, use the type the vehicle maker recommends, which is stamped on the master cylinder reservoir lid.

    Reviews

    No reviews yet — be the first to review this product.

    Write a Review