Remanufactured Mass Air Flow Sensor for 1996-2000 Ford Mustang & More - A1 CARDONE 74-9549

$108.99

Vehicles this part fits

    Part number: 74-9549
    UPC: 082617505291
    Weight: 1.60 LBS
    Item Package Quantity: 1
    $108.99
    Adding to cart… The item has been added

    Have questions?

    CARDONE Reman Mass Air Flow Sensor P/N:74-9549
    CARDONE Reman Mass Air Flow Sensor P/N:74-9549
    $108.99
    $108.99

    A1 CARDONE 74-9549 mass air flow sensor for the 1996-2000 Ford Mustang V6 3.8L and other vehicles measures the air entering the engine and sends that reading to the engine control system. This is a remanufactured unit with an aluminum housing.

    • Output curves and tolerances held to spec for accurate scan tool readings and engine control feedback
    • 100% re-soldering of critical components for secure electrical connections and longer product life
    • On-car vehicle validation routines check durability and performance requirements
    • 100% tested with automated computer test equipment for full functionality
    • Components rated for demanding temperature variations
    • Remanufacturing cuts the energy and raw material needed to make a new part by 80%

    Quick facts

    • Part: A1 CARDONE 74-9549 mass air flow sensor
    • Fits: 1996-2000 Ford Mustang V6 3.8L and other vehicles
    • Material: Aluminum (housing)
    • Condition: Remanufactured

    Hesitation, stalling, poor fuel economy or poor engine performance can come from a failing mass air flow sensor. Before you replace it, rule out other causes by reading diagnostic trouble codes with a scanner and, with the engine off and cool, looking over the sensor element for damage or a burnt smell.

    Fits

    The 1996-2000 Ford Mustang V6 3.8L, the 1995-2000 Ford Ranger V6 4.0L and the 1996-1998 Ford Explorer V6 4.0L or V8 5.0L all take this mass air flow sensor, as do many other vehicles; each takes one. If your car is not named here, look up its year, make and model in the "Vehicles it fits" section further down this page.

    Specifications

    Fit and size

    • Quantity per vehicle: 1
    • Outlet connection diameter: 3.3 in (80.85 mm)
    • Connector: 1, rectangular, male
    • Terminals: 4, pin type, male
    • Mounting holes: 4
    • Mounting type: bolt-on; hose clamp

    Build and materials

    • Housing material: aluminum
    • Contains electronic components: circuit board
    • Condition: remanufactured
    • Country of origin: Mexico

    In the box

    One mass air flow sensor and one instruction sheet. Mounting hardware, a mounting bracket and a wiring harness are not included, so plan on new fasteners.

    Interchange: F57F12B579BA · F57F12B579CA · F57F12B579DA · F57Z12A579B · F57Z12A579CA · F57Z12B579B · F57Z12B579CA · F57Z12B579DA · ZZM213210 · ZZM513210

    Product information is for general reference and may contain errors. See our Disclaimer.

    This part cross-references / interchanges with the following part numbers:

    F57F12B579BA, F57F12B579CA, F57F12B579DA, F57Z12A579B, F57Z12A579CA, F57Z12B579B, F57Z12B579CA, F57Z12B579DA, ZZM213210, ZZM513210

    Frequently Asked Questions

    Is this the right mass air flow sensor for a 1995-2000 Ford Ranger V6 4.0L?

    Yes. A1 CARDONE 74-9549 fits the 1995-2000 Ford Ranger V6 4.0L, and each vehicle takes one sensor. For another car, look up its year, make and model in the "Vehicles it fits" section.

    Does this A1 CARDONE mass air flow sensor come with a bracket or wiring harness?

    No. The 74-9549 package holds the mass air flow sensor and an instruction sheet. Mounting hardware, the mounting bracket and the wiring harness are not included.

    What size is the outlet connection on this remanufactured mass air flow sensor?

    The outlet connection diameter is 3.3 inches (80.85 mm). The sensor has one rectangular male connector with 4 male pin terminals.

    What are the most common failures inside these mass air flow sensors?

    Cracked circuit boards, burnt sensing elements, poor solder joints, deteriorated conformal coating and loose circuit board components. This unit has all critical components re-soldered.

    How is the remanufactured 74-9549 sensor tested?

    Every unit is tested on automated computer test equipment, and on-car vehicle validation routines check form, fit, durability and performance requirements.

    Reviews

    No reviews yet — be the first to review this product.

    Write a Review