Remanufactured Power Steering Pump for 2000 Ford Focus - A1 CARDONE 20-293

$126.99

Vehicles this part fits

    Part number: 20-293
    UPC: 082617614641
    Weight: 6.00 LBS
    Item Package Quantity: 1
    $126.99
    Adding to cart… The item has been added

    Have questions?

    CARDONE Reman Power Steering Pump P/N:20-293
    CARDONE Reman Power Steering Pump P/N:20-293
    $126.99
    $126.99

    A1 CARDONE 20-293 power steering pump for the 2000 Ford Focus is remanufactured and supplies hydraulic pressure for steering assist. Each unit is engineered to meet or exceed O.E. performance.

    • 100% new O-rings and HNBR seals to prevent leaks; HNBR resists breakdown at high temperatures
    • Shafts surfaced to precise specifications to reduce premature seal wear
    • Campacs, spool valves and other critical components triple-tested
    • Pressure relief valve tested and calibrated
    • Final assembly computer-tested for pressure, bypass, fluid flow, valve operation, steering effort and noise
    • Hydraulic efficiency test on every unit

    Quick facts

    • Part: A1 CARDONE 20-293 power steering pump
    • Fits: 2000 Ford Focus
    • Material: Cast iron housing
    • Condition: Remanufactured

    A constant whine, heavy steering or fluid weeping around the pump can mean it is wearing out. These signs alone do not prove the pump is at fault, because a binding steering component can also make the wheel hard to turn.

    Fits

    This listing is one pump, a direct-fit replacement for the 2000 Ford Focus, which takes a single pump.

    Specifications

    Fit and size

    • Quantity per vehicle: 1
    • Inlet diameter: 19.96 mm (0.786 in)
    • Inlet: barb, quantity 1
    • Outlet: threaded, quantity 1
    • Outlet thread size: 16x1.5
    • Hose port type: O-ring
    • Shaft type: press-on

    Build and materials

    • Condition: Remanufactured
    • Housing material: cast iron
    • Seals: HNBR, with new O-rings
    • Reservoir: remote
    • Country of origin: Mexico

    In the box

    One power steering pump, one instruction sheet and one sealing kit. The pulley, mounting hardware, reservoir, reservoir cap and filter are not included, so plan on new mounting hardware rather than reusing the old.

    Interchange: YS4Z3A674BERM

    Product information is for general reference and may contain errors. See our Disclaimer.

    This part cross-references / interchanges with the following part numbers:

    YS4Z3A674BERM

    Frequently Asked Questions

    Is the A1 CARDONE 20-293 a power steering pump replacement for the 2000 Ford Focus?

    Yes. The A1 CARDONE 20-293 is a direct-fit replacement for the 2000 Ford Focus, and the Focus takes one pump.

    Yes. The A1 CARDONE 20-293 is a direct-fit replacement for the 2000 Ford Focus, and the Focus takes one pump.

    Does this A1 CARDONE power steering pump come with a pulley?

    No. The A1 CARDONE 20-293 does not include the pulley, mounting hardware, reservoir, reservoir cap or filter; it comes with the pump, an instruction sheet and a sealing kit.

    No. The A1 CARDONE 20-293 does not include the pulley, mounting hardware, reservoir, reservoir cap or filter; it comes with the pump, an instruction sheet and a sealing kit.

    Does this A1 CARDONE power steering pump come with a pulley?

    No. The A1 CARDONE 20-293 does not include the pulley, mounting hardware, reservoir, reservoir cap or filter; it comes with the pump, an instruction sheet and a sealing kit.

    No. The A1 CARDONE 20-293 does not include the pulley, mounting hardware, reservoir, reservoir cap or filter; it comes with the pump, an instruction sheet and a sealing kit.

    What size is the outlet thread on this power steering pump?

    The outlet is threaded with a 16x1.5 thread size, and the inlet is a barb with a 19.96 mm (0.786 in) diameter. The hose port type is O-ring.

    The outlet is threaded with a 16x1.5 thread size, and the inlet is a barb with a 19.96 mm (0.786 in) diameter. The hose port type is O-ring.

    What size is the outlet thread on this power steering pump?

    The outlet is threaded with a 16x1.5 thread size, and the inlet is a barb with a 19.96 mm (0.786 in) diameter. The hose port type is O-ring.

    The outlet is threaded with a 16x1.5 thread size, and the inlet is a barb with a 19.96 mm (0.786 in) diameter. The hose port type is O-ring.

    Which seals does this remanufactured pump use?

    This pump is built with 100% new O-rings and HNBR seals, and its shafts are surfaced to precise specifications to reduce premature seal wear.

    This pump is built with 100% new O-rings and HNBR seals, and its shafts are surfaced to precise specifications to reduce premature seal wear.

    Which seals does this remanufactured pump use?

    This pump is built with 100% new O-rings and HNBR seals, and its shafts are surfaced to precise specifications to reduce premature seal wear.

    This pump is built with 100% new O-rings and HNBR seals, and its shafts are surfaced to precise specifications to reduce premature seal wear.

    My old pulley is loose on the replacement pump shaft. What should I do?

    The old pulley may have cracked on removal, or a mushroomed shaft may have enlarged its bore. In either case the pulley must be replaced; this pump has a press-on shaft.

    The old pulley may have cracked on removal, or a mushroomed shaft may have enlarged its bore. In either case the pulley must be replaced; this pump has a press-on shaft.

    My old pulley is loose on the replacement pump shaft. What should I do?

    The old pulley may have cracked on removal, or a mushroomed shaft may have enlarged its bore. In either case the pulley must be replaced; this pump has a press-on shaft.

    The old pulley may have cracked on removal, or a mushroomed shaft may have enlarged its bore. In either case the pulley must be replaced; this pump has a press-on shaft.

    Frequently Asked Questions

    Is the A1 CARDONE 20-293 a power steering pump replacement for the 2000 Ford Focus?

    Yes. The A1 CARDONE 20-293 is a direct-fit replacement for the 2000 Ford Focus, and the Focus takes one pump.

    Yes. The A1 CARDONE 20-293 is a direct-fit replacement for the 2000 Ford Focus, and the Focus takes one pump.

    Does this A1 CARDONE power steering pump come with a pulley?

    No. The A1 CARDONE 20-293 does not include the pulley, mounting hardware, reservoir, reservoir cap or filter; it comes with the pump, an instruction sheet and a sealing kit.

    No. The A1 CARDONE 20-293 does not include the pulley, mounting hardware, reservoir, reservoir cap or filter; it comes with the pump, an instruction sheet and a sealing kit.

    Does this A1 CARDONE power steering pump come with a pulley?

    No. The A1 CARDONE 20-293 does not include the pulley, mounting hardware, reservoir, reservoir cap or filter; it comes with the pump, an instruction sheet and a sealing kit.

    No. The A1 CARDONE 20-293 does not include the pulley, mounting hardware, reservoir, reservoir cap or filter; it comes with the pump, an instruction sheet and a sealing kit.

    What size is the outlet thread on this power steering pump?

    The outlet is threaded with a 16x1.5 thread size, and the inlet is a barb with a 19.96 mm (0.786 in) diameter. The hose port type is O-ring.

    The outlet is threaded with a 16x1.5 thread size, and the inlet is a barb with a 19.96 mm (0.786 in) diameter. The hose port type is O-ring.

    What size is the outlet thread on this power steering pump?

    The outlet is threaded with a 16x1.5 thread size, and the inlet is a barb with a 19.96 mm (0.786 in) diameter. The hose port type is O-ring.

    The outlet is threaded with a 16x1.5 thread size, and the inlet is a barb with a 19.96 mm (0.786 in) diameter. The hose port type is O-ring.

    Which seals does this remanufactured pump use?

    This pump is built with 100% new O-rings and HNBR seals, and its shafts are surfaced to precise specifications to reduce premature seal wear.

    This pump is built with 100% new O-rings and HNBR seals, and its shafts are surfaced to precise specifications to reduce premature seal wear.

    Which seals does this remanufactured pump use?

    This pump is built with 100% new O-rings and HNBR seals, and its shafts are surfaced to precise specifications to reduce premature seal wear.

    This pump is built with 100% new O-rings and HNBR seals, and its shafts are surfaced to precise specifications to reduce premature seal wear.

    My old pulley is loose on the replacement pump shaft. What should I do?

    The old pulley may have cracked on removal, or a mushroomed shaft may have enlarged its bore. In either case the pulley must be replaced; this pump has a press-on shaft.

    The old pulley may have cracked on removal, or a mushroomed shaft may have enlarged its bore. In either case the pulley must be replaced; this pump has a press-on shaft.

    My old pulley is loose on the replacement pump shaft. What should I do?

    The old pulley may have cracked on removal, or a mushroomed shaft may have enlarged its bore. In either case the pulley must be replaced; this pump has a press-on shaft.

    The old pulley may have cracked on removal, or a mushroomed shaft may have enlarged its bore. In either case the pulley must be replaced; this pump has a press-on shaft.

    Reviews

    No reviews yet — be the first to review this product.

    Write a Review