Remanufactured Rack and Pinion for 2009-2014 Dodge Avenger & More - A1 CARDONE 22-3021

$357.99

Vehicles this part fits

    Part number: 22-3021
    UPC: 082617854061
    Weight: 23.50 LBS
    Item Package Quantity: 1
    $357.99
    Adding to cart… The item has been added

    Have questions?

    CARDONE Reman Rack and Pinion Assembly P/N:22-3021
    CARDONE Reman Rack and Pinion Assembly P/N:22-3021
    $357.99
    $357.99

    A1 CARDONE 22-3021 rack and pinion for the 2009-2014 Dodge Avenger and other vehicles turns steering wheel rotation into sideways wheel movement. This remanufactured unit is also called a rack and pinion assembly, and each one is re-engineered, built and tested.

    • Protective coating applied to each unit, where applicable
    • 100% performance testing of each rack and pinion
    • 100% hydraulic testing for flow, leakage and performance, where applicable
    • Racks surfaced to precise specifications to prevent leaking between chambers
    • New o-rings, lip seals, spool valve seals and rack donut seals, where applicable
    • Valve housings with polished micro-finish sleeves, where applicable

    Quick facts

    • Part: A1 CARDONE 22-3021 rack and pinion
    • Also called: rack and pinion assembly
    • Fits: 2009-2014 Dodge Avenger and other vehicles
    • Condition: Remanufactured

    Fluid leaking around the rack, loose steering or a wheel that will not return to center after a turn can mean the rack is worn. Worn tie rods, a weak pump or alignment can feel the same, so rule those out before replacing the rack, starting with the power steering fluid level (engine off and cool) and any drips on the ground where the car was parked.

    Fits

    This rack and pinion fits the 2009-2014 Dodge Avenger, the 2011-2014 Chrysler 200 and the 2009-2010 Chrysler Cirrus, along with other vehicles. If your car is not named here, look it up in the "Vehicles it fits" section. The 2009-2014 Dodge Avenger takes one.

    Specifications

    Fit and size

    • Quantity per vehicle: 1
    • Mounting hole quantity: 2
    • Total turns lock to lock: 3
    • Input shaft type: double flat
    • Steering input shaft diameter: 0.625 in (15.87 mm)
    • Inlet line fitting diameter: 0.702 in (17.83 mm), male
    • Outlet line fitting diameter: 0.459 in (11.66 mm), male

    Build and materials

    • Condition: Remanufactured
    • Inner tie rods: included
    • Sealing kit: included
    • Country of origin: Mexico

    In the box

    One rack and pinion with its inner tie rods, a sealing kit and an instruction sheet. Outer tie rods, mounting brackets and mounting hardware are not included, so plan on new hardware rather than reusing the old.

    Installation notes

    • An instruction sheet comes with the unit.
    • The power steering system must be bled after installation, which may take a few attempts depending on the system design.

    Interchange: 4743875AF · 5154524AA · 5154524AB · 5154524AC · 5272822AC · 5272822AD · 5272822AE · 5272822AF · 5272822AJ · 68048697AA

    Product information is for general reference and may contain errors. See our Disclaimer.

    This part cross-references / interchanges with the following part numbers:

    4743875AF, 5154524AA, 5154524AB, 5154524AC, 5272822AC, 5272822AD, 5272822AE, 5272822AF, 5272822AJ, 68048697AA

    Frequently Asked Questions

    Is this a Dodge Avenger rack and pinion for model years 2009-2014?

    Yes. A1 CARDONE 22-3021 fits the 2009-2014 Dodge Avenger and the 2011-2014 Chrysler 200. Open the "Vehicles it fits" section to check other models and engines.

    Yes, A1 CARDONE 22-3021 fits the 2009-2014 Dodge Avenger, which takes one; other cars are covered in the "Vehicles it fits" section.

    Are the tie rods included with this rack and pinion?

    Yes for the inner tie rods, no for the outer ones. A sealing kit and an instruction sheet are included; mounting hardware and mounting brackets are not.

    A1 CARDONE 22-3021 includes the inner tie rods, a sealing kit and an instruction sheet. Outer tie rods, mounting brackets and mounting hardware are not included.

    Does this A1 CARDONE steering rack include tie rods?

    Yes for the inner tie rods, no for the outer ones. A sealing kit and an instruction sheet are included; mounting hardware and mounting brackets are not.

    A1 CARDONE 22-3021 includes the inner tie rods, a sealing kit and an instruction sheet. Outer tie rods, mounting brackets and mounting hardware are not included.

    What size are the input shaft and line fittings on this rack and pinion?

    The double-flat steering input shaft is 0.625 in (15.87 mm). The inlet line fitting is 0.702 in (17.83 mm) and the outlet is 0.459 in (11.66 mm), both male.

    The inlet fitting is 0.702 in (17.83 mm) and the outlet fitting is 0.459 in (11.66 mm), both male. The input shaft is 0.625 in (15.87 mm) with a double-flat type.

    What size are the line fittings on this rack and pinion?

    The double-flat steering input shaft is 0.625 in (15.87 mm). The inlet line fitting is 0.702 in (17.83 mm) and the outlet is 0.459 in (11.66 mm), both male.

    The inlet fitting is 0.702 in (17.83 mm) and the outlet fitting is 0.459 in (11.66 mm), both male. The input shaft is 0.625 in (15.87 mm) with a double-flat type.

    Why is my power steering pump whining after installing a new rack and pinion?

    With A1 CARDONE 22-3021, the most likely cause is air in the system. The steering system must be bled, which may take a few attempts depending on the system's design.

    Air in the system is the most likely cause, and the steering system must be bled. It may take a few attempts depending on the design of the system.

    Why is my power steering pump whining after I installed a new rack?

    With A1 CARDONE 22-3021, the most likely cause is air in the system. The steering system must be bled, which may take a few attempts depending on the system's design.

    Air in the system is the most likely cause, and the steering system must be bled. It may take a few attempts depending on the design of the system.

    Can I keep driving with a leaking rack and pinion assembly?

    No. A leak or heavy play in the steering needs prompt inspection or replacement, since steering is a safety system. A shop can test the rack, pump and tie rods.

    Yes. 5272822AC is one of the numbers this A1 CARDONE 22-3021 rack and pinion replaces.

    Does 22-3021 replace part number 5272822AC?

    No. A leak or heavy play in the steering needs prompt inspection or replacement, since steering is a safety system. A shop can test the rack, pump and tie rods.

    Yes. 5272822AC is one of the numbers this A1 CARDONE 22-3021 rack and pinion replaces.

    Frequently Asked Questions

    Is this a rack and pinion for the 2009-2014 Dodge Avenger?

    Yes. A1 CARDONE 22-3021 fits the 2009-2014 Dodge Avenger and the 2011-2014 Chrysler 200. Open the "Vehicles it fits" section to check other models and engines.

    Yes, A1 CARDONE 22-3021 fits the 2009-2014 Dodge Avenger, which takes one; other cars are covered in the "Vehicles it fits" section.

    Are the tie rods included with this rack and pinion?

    Yes for the inner tie rods, no for the outer ones. A sealing kit and an instruction sheet are included; mounting hardware and mounting brackets are not.

    A1 CARDONE 22-3021 includes the inner tie rods, a sealing kit and an instruction sheet. Outer tie rods, mounting brackets and mounting hardware are not included.

    Does this A1 CARDONE steering rack include tie rods?

    Yes for the inner tie rods, no for the outer ones. A sealing kit and an instruction sheet are included; mounting hardware and mounting brackets are not.

    A1 CARDONE 22-3021 includes the inner tie rods, a sealing kit and an instruction sheet. Outer tie rods, mounting brackets and mounting hardware are not included.

    What size are the input shaft and line fittings on this rack and pinion?

    The double-flat steering input shaft is 0.625 in (15.87 mm). The inlet line fitting is 0.702 in (17.83 mm) and the outlet is 0.459 in (11.66 mm), both male.

    The inlet fitting is 0.702 in (17.83 mm) and the outlet fitting is 0.459 in (11.66 mm), both male. The input shaft is 0.625 in (15.87 mm) with a double-flat type.

    What size are the line fittings on this rack and pinion?

    The double-flat steering input shaft is 0.625 in (15.87 mm). The inlet line fitting is 0.702 in (17.83 mm) and the outlet is 0.459 in (11.66 mm), both male.

    The inlet fitting is 0.702 in (17.83 mm) and the outlet fitting is 0.459 in (11.66 mm), both male. The input shaft is 0.625 in (15.87 mm) with a double-flat type.

    Why is my power steering pump whining after installing a new rack and pinion?

    With A1 CARDONE 22-3021, the most likely cause is air in the system. The steering system must be bled, which may take a few attempts depending on the system's design.

    Air in the system is the most likely cause, and the steering system must be bled. It may take a few attempts depending on the design of the system.

    Why is my power steering pump whining after I installed a new rack?

    With A1 CARDONE 22-3021, the most likely cause is air in the system. The steering system must be bled, which may take a few attempts depending on the system's design.

    Air in the system is the most likely cause, and the steering system must be bled. It may take a few attempts depending on the design of the system.

    Can I keep driving with a leaking rack and pinion assembly?

    No. A leak or heavy play in the steering needs prompt inspection or replacement, since steering is a safety system. A shop can test the rack, pump and tie rods.

    Yes. 5272822AC is one of the numbers this A1 CARDONE 22-3021 rack and pinion replaces.

    Does 22-3021 replace part number 5272822AC?

    No. A leak or heavy play in the steering needs prompt inspection or replacement, since steering is a safety system. A shop can test the rack, pump and tie rods.

    Yes. 5272822AC is one of the numbers this A1 CARDONE 22-3021 rack and pinion replaces.

    Reviews

    No reviews yet — be the first to review this product.

    Write a Review