Front Left Lower Control Arm with Ball Joint for 2018-2021 Mercedes-Benz S560 & More - Delphi TC9178

$165.99
WARNING:California Proposition 65▾

Vehicles this part fits

    Part number: TC9178
    UPC: 689604409053
    Condition: New
    Weight: 6.40 LBS
    Item Package Quantity: 1
    $165.99
    Adding to cart… The item has been added

    Have questions?

    Delphi Suspension Control Arm and Ball Joint Assembly P/N:TC9178
    Delphi Suspension Control Arm and Ball Joint Assembly P/N:TC9178
    $165.99
    $165.99

    Delphi TC9178 front left lower control arm with ball joint for the 2018-2021 Mercedes-Benz S560 and other vehicles connects the front wheel to the chassis through a pivoting ball joint. The control arm and ball joint assembly comes with the joint attached, so one part replaces both.

    • Tested at temperatures below -40 °C and above 120 °C and through 720 hours of salt spray
    • 100% crack detection and ultrasonic flaw detection on every control arm
    • Ball studs machined to micron tolerances for durability and smooth joint operation
    • Robot-welded arm for consistent quality
    • Anti-corrosion protection applied to each part

    Quick facts

    • Part: Delphi TC9178 control arm with ball joint
    • Also called: control arm and ball joint assembly
    • Fits: 2018-2021 Mercedes-Benz S560 and other vehicles
    • Position: Front Left Lower Rearward
    • Condition: New

    A clunk over bumps, uneven tire wear or loose-feeling steering can come from a worn ball joint or arm, but bushings, shocks and alignment can produce the same signs, so pin down the source before buying. A shop can inspect the ball joint boot and measure play in the joint. Front arms are normally replaced in left and right pairs, and this listing is one arm for the front left.

    Fits

    This arm is listed for a wide range of Mercedes-Benz models, including the 2018-2020 Mercedes-Benz Maybach S650 and the 2018-2020 Mercedes-Benz S450. If your car is not named here, look up its year and model in the "Vehicles it fits" section to see whether it is listed.

    Specifications

    Fit and size

    • Position: front left, lower, rearward
    • Quantity per application: 1 for the front left
    • Sold individually: one per listing

    Build and materials

    • Type: control arm with ball joint
    • Construction: robot-welded
    • Ball studs: machined to micron tolerances
    • Corrosion protection: anti-corrosion protection applied
    • Condition: New

    In the box

    One control arm with ball joint. The front left takes one; the front right is a separate part ordered on its own.

    Interchange: 526-273 · 222 330 01 07 · A 222 330 01 07
    1028059 · 222330010728 · CMS101492 · X31CJ0336

    Product information is for general reference and may contain errors. See our Disclaimer.

    This part cross-references / interchanges with the following part numbers:

    1028059, 526-273, 222 330 01 07, 222330010728, A 222 330 01 07, CMS101492, X31CJ0336

    Frequently Asked Questions

    Does the Delphi TC9178 fit the 2018-2021 Mercedes-Benz S560?

    Yes. Delphi TC9178 is the front left lower rearward control arm with ball joint for the 2018-2021 Mercedes-Benz S560, and the listing is one arm for that corner.

    Is the ball joint already part of the TC9178, or do I buy one separately?

    Yes, the ball joint is part of the assembly. Delphi TC9178 is a single control arm with its ball joint attached, so no separate joint is needed.

    Which corner of the car does this lower control arm go on?

    This arm is the front left lower rearward position. The front right uses its own separate arm.

    Can a loose ball joint on a front lower control arm cause a clunk?

    It can. A clunk over bumps or uneven tire wear may come from a worn ball joint, though other suspension parts cause similar signs, and a shop can measure joint play.

    What inspection does a Delphi control arm go through?

    Each Delphi control arm gets 100% crack detection and ultrasonic flaw detection, and its ball studs are machined to micron tolerances. The arm is robot-welded and has anti-corrosion protection.

    Reviews

    No reviews yet — be the first to review this product.

    Write a Review