Delphi Suspension Stabilizer Bar Bushing Kit P/N:TD4554W
$11.99
(You save)
Quiet a rattling stabilizer bar and keep body roll in check with the Delphi Suspension Stabilizer Bar Bushing Kit (TD4554W). These bushings mount at the front bar-to-strut-rod position, cushioning the stabilizer bar where it connects so it can resist body sway while isolating road noise and vibration. It's a direct-fit replacement for a long list of classic Chrysler, Dodge and Plymouth applications, including the 1965-1971 Chrysler 300, 1965-1981 Chrysler New Yorker and Newport, 1973-1978 Dodge Charger, 1965-1978 Dodge Monaco, 1968-1972 Plymouth Barracuda and 1970-1975 Plymouth Road Runner — see the Buyer's Guide tab for the full list.
Built to OE standards: Delphi applies its OE engineering to its aftermarket steering and suspension portfolio, with dimensional and material analysis for compatibility between the OE and aftermarket part.
Validated to the extreme: tested to withstand temperatures below -40°C and over 120°C and exposed to 720 hours of salt spray.
Manufactured for consistent life: made to reduce noise as the bar works.
Smoother ride: designed to help restore the vehicle's smooth ride when worn bushings are the cause.
Signs these bushings may need replacing include clunking or rattling from the stabilizer bar over uneven roads, increased body lean in turns, and cracked or deteriorated rubber. Also sold as a stabilizer bar bushing kit.
Where on the vehicle does the Delphi TD4554W kit fit?
These bushings mount at the front bar-to-strut-rod position, cushioning the stabilizer bar where it attaches so it can control body sway while isolating road noise.
Which vehicles does this kit fit?
It's a direct-fit for many classic Chrysler, Dodge and Plymouth models, such as the 1975-1979 Chrysler Cordoba, 1973-1976 Dodge Coronet and 1970-1972 Plymouth Cuda. See the Buyer's Guide tab for the full list.
Is a sway bar bushing kit the same as a stabilizer bar bushing kit?
Yes. Sway bar and stabilizer bar are two names for the same component, so this is both a sway bar bushing kit and a stabilizer bar bushing kit.
How were these Delphi bushings tested?
Delphi tests to OE performance standards: the parts withstand temperatures below -40°C and over 120°C and are exposed to 720 hours of salt spray, backed by dimensional and material analysis.
What are signs my sway bar bushings need replacing?
Common signs include clunking or rattling from the stabilizer bar over uneven roads, increased body lean when cornering, and cracked or deteriorated rubber. Diagnose the cause before replacing.
Write a Review
Delphi
Delphi Suspension Stabilizer Bar Bushing Kit P/N:TD4554W
Quiet stabilizer-bar rattle and help keep the rear sway bar properly located with the Delphi Sway Bar Bushing Kit TD922W, a rear-position replacement cataloged for the 2006-2011 Land Rover Range...
Keep the front stabilizer bar located and quiet with the Delphi Suspension Stabilizer Bar Bushing Kit (TD1265W). These bushings cushion the front sway bar where it mounts to the chassis, letting the...
Help quiet a clunking front sway bar and keep the stabilizer bar located with the Delphi Suspension Stabilizer Bar Bushing Kit TD1136W. This front stabilizer bar bushing kit is a direct-fit...
Keep the front stabilizer bar quiet and firmly located with the Delphi Suspension Stabilizer Bar Bushing Kit (TD955W). This front sway bar bushing kit drops in as a direct-fit replacement for the...
Quiet a clunking front sway bar and keep your Hyundai's stabilizer working the way it should with the Delphi Suspension Stabilizer Bar Bushing Kit TD1264W. This front stabilizer bar bushing kit...
WARNING:
These products can expose you to chemicals including lead and phthalates, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
