Remanufactured Front Left Brake Caliper for 2016-2019 Chevrolet Cruze - CARDONE REMAN 18-B5576

$166.99

Vehicles this part fits

    Part number: 18-B5576
    UPC: 884548283893
    Weight: 11.90 LBS
    Item Package Quantity: 1
    $166.99
    Adding to cart… The item has been added

    Have questions?

    CARDONE Reman Disc Brake Caliper P/N:18-B5576
    CARDONE Reman Disc Brake Caliper P/N:18-B5576
    $166.99
    $166.99

    CARDONE REMAN 18-B5576 front left brake caliper for the 2016-2019 Chevrolet Cruze clamps the brake pads against the rotor to slow the wheel. This remanufactured caliper is unloaded, so it comes without pads, and it includes the mounting bracket.

    • Phenolic piston that resists cracking and pitting
    • New high temperature EPDM rubber seals replace the worn ones
    • Every caliper is 100% pressure-tested
    • Rust inhibitor treatment and a powder-coated finish
    • New bleeder screw for a positive seal, plus plastic cap plugs that protect the brake port threads

    Quick facts

    • Part: CARDONE REMAN 18-B5576 brake caliper
    • Also called: disc brake caliper
    • Fits: 2016-2019 Chevrolet Cruze
    • Position: Front left
    • Material: Cast iron
    • Condition: Remanufactured

    A disc brake caliper that sticks or leaks can show up as the car pulling to one side, uneven pad wear or fluid around the caliper. Sticky slide pins or a collapsed brake hose can produce a pull as well. During a brake service, with the engine off and cool, look over the pins, the hose and the caliper for leaks or binding before you replace it.

    Fits

    It fits the 2016-2019 Chevrolet Cruze. The front left takes one caliper, and this listing is that one; the front right is a separate part ordered on its own, and the two sides are normally replaced together.

    Specifications

    Fit and size

    • Position: Front left
    • Quantity for the front left: 1
    • Piston quantity: 1
    • Piston diameter: 2.359 in (59.9 mm)
    • Inlet port size: 0.394 in, banjo fitting, M10x1.5 thread
    • Mounting hole diameter: 0.551 in (13.99 mm), M14X2.0 thread
    • Bleeder thread size: M10x1.0

    Build and materials

    • Type: Floating caliper, unloaded, with bracket
    • Condition: Remanufactured
    • Caliper casting material: Cast iron
    • Piston material: Phenolic
    • Finish: Powder coated, with a rust resistant coating
    • Country of origin: Mexico

    In the box

    One caliper with its mounting bracket, a hardware kit with abutment clips, a bleeder screw and dust boots, and an instruction sheet. Brake pads, mounting bolts and the bleeder screw cap are not included, so plan on new mounting bolts rather than reusing the old ones.

    Installation notes

    • An instruction sheet comes with the caliper.
    • Silicone grease is used on floating caliper mounting pins.
    • Use the brake fluid the original manufacturer specifies; the type is stamped on the master cylinder reservoir lid.

    Interchange: 13515456

    Product information is for general reference and may contain errors. See our Disclaimer.

    This part cross-references / interchanges with the following part numbers:

    13515456

    Frequently Asked Questions

    Is this front left caliper the right Chevy Cruze brake caliper for a 2016-2019 car?

    Yes. CARDONE REMAN 18-B5576 is the front left brake caliper for the 2016-2019 Chevrolet Cruze. The front right side is a separate part.

    Does the 18-B5576 caliper come with brake pads and mounting bolts?

    No. CARDONE REMAN 18-B5576 comes with the bracket, a hardware kit and an instruction sheet. Pads and mounting bolts are not included.

    Is the piston in this remanufactured caliper phenolic or steel?

    Phenolic. This floating caliper has a single phenolic piston, 2.359 in (59.9 mm) across, that resists cracking and pitting.

    Can a sticking caliper make the car pull to one side when braking?

    Yes, it can, though other brake problems can also cause a pull. Have a shop inspect the brakes promptly rather than keep driving.

    What grease goes on the mounting pins of this floating caliper?

    Silicone grease goes on floating caliper mounting pins. For brake fluid, use the type the vehicle's maker specifies, stamped on the master cylinder reservoir lid.

    Reviews

    No reviews yet — be the first to review this product.

    Write a Review