Front Lower Ball Joint for 1975-1999 Chevrolet P30 & More - Dorman 533-196

$32.99

Vehicles this part fits

    Part number: 533-196
    UPC: 194883728127
    Condition: New
    Weight: 2.60 LBS
    Item Package Quantity: 1
    $32.99
    Adding to cart… The item has been added

    Have questions?

    Dorman - OE Solutions Suspension Ball Joint P/N:533-196
    Dorman - OE Solutions Suspension Ball Joint P/N:533-196
    $32.99
    $32.99

    Dorman 533-196 front lower ball joint for the 1975-1999 Chevrolet P30 and other vehicles gives the steering knuckle a pivoting connection to the suspension. This Dorman ball joint is a direct replacement that fits and performs like the original equipment on specific vehicles.

    • Steel construction with a rubber dust boot
    • Tapered stud with an 11/16 in thread diameter and 35.5 mm thread length
    • Press-in housing with a 58.7 mm press-fit diameter
    • Greaseable design with a cotter pin hole
    • Replaces just the failed ball joint instead of the complete assembly

    Quick facts

    • Part: Dorman 533-196 ball joint
    • Also called: suspension ball joint
    • Fits: 1975-1999 Chevrolet P30 and other vehicles
    • Position: Front lower
    • Material: Steel
    • Condition: New

    A worn suspension ball joint can show up as a clunk over bumps, loose or wandering steering, or uneven tire wear. Before replacing it, look at the dust boot for tears or grease leaking out, since a clunk or loose steering can also have other sources in the suspension or steering.

    Fits

    This ball joint is listed for a wide range of Chevrolet and GMC models, led by the 1975-1999 Chevrolet P30, the 1979-1999 GMC P3500 and the 1975-1978 GMC P35. If your vehicle is not one of those three, find its year and model in the "Vehicles it fits" section. This listing is one ball joint; the front lower position takes one on each side of the axle, and both sides are normally replaced together.

    Specifications

    Fit and size

    • Position: Front lower
    • Quantity per vehicle: 2
    • Stud tapered end 1 diameter: 27.2 mm
    • Stud tapered end 2 diameter: 22 mm
    • Stud taper per foot: 2 in
    • Housing press-fit diameter: 58.7 mm
    • Maximum outside diameter: 61 mm
    • Stud thread diameter: 11/16 in
    • Stud thread length: 35.5 mm
    • Wrench size: 12 mm

    Build and materials

    • Type: Threaded, tapered stud
    • Mounting type: Press-in
    • Material: Steel
    • Dust boot material: Rubber
    • Greaseable: Yes
    • Condition: New
    • Country of origin: Taiwan

    In the box

    One ball joint with a castle nut, and the dust boot is already installed. Washers, bushings and mounting bolts are not included, so plan on new bolts.

    Installation notes

    • A ball joint press tool is normally required for installation.

    Interchange: 610.66048
    TC6388 · 9760950 · K6175T · K6511 · FA1103 · FA1103E · FA1103FT · GK6511 · MK6175T · MK6511 · JBJ983

    Product information is for general reference and may contain errors. See our Disclaimer.

    This part cross-references / interchanges with the following part numbers:

    610.66048, TC6388, 9760950, K6175T, K6511, FA1103, FA1103E, FA1103FT, GK6511, MK6175T, MK6511, JBJ983

    Frequently Asked Questions

    Is the Dorman 533-196 ball joint right for the 1975-1999 Chevrolet P30?

    Yes. Dorman 533-196 is a front lower ball joint listed for the 1975-1999 Chevrolet P30. The "Vehicles it fits" section shows the other vehicles it is listed for.

    Does this ball joint come with a castle nut?

    Yes. The castle nut is included and the dust boot is already installed on the joint. Washers, bushings and mounting bolts are not included.

    What size is the stud on the Dorman 533-196 ball joint?

    The stud is tapered, 27.2 mm across at one end and 22 mm at the other, with a taper of 2 in per foot. Its thread is 11/16 in in diameter and 35.5 mm long.

    What tool does this press-in ball joint need for installation?

    A ball joint press tool is normally required for the press-in mounting. The housing has a 58.7 mm press-fit diameter.

    Does this ball joint replace number K6511?

    Yes. K6511 is on the Interchange line for Dorman 533-196, along with K6175T and MK6511.

    Reviews

    No reviews yet — be the first to review this product.

    Write a Review