Rear Right Brake Caliper for 2001-2003 Toyota Highlander - Nugeon 99-01627A

$145.99
WARNING:California Proposition 65▾

Vehicles this part fits

    Part number: 99-01627A
    UPC: 736749371162
    Condition: New
    Weight: 7.30 LBS
    Item Package Code: EA
    Part Has Core (Y/N): N
    Item Package Quantity: 1
    $145.99
    Adding to cart… The item has been added

    Have questions?

    Nugeon Disc Brake Caliper P/N:99-01627A
    Nugeon Disc Brake Caliper P/N:99-01627A
    $145.99
    $145.99

    Nugeon 99-01627A rear right brake caliper for the 2001-2003 Toyota Highlander clamps the brake pads against the rotor to slow the wheel. This Nugeon brake caliper is remanufactured and takes the place of a worn or leaking one at that wheel.

    • Floating caliper design with a single steel piston
    • Cast iron housing with a rust preventative finish
    • Banjo bolt inlet fitting for the brake hose connection
    • Caliper bracket, slides, dust boots and bleeder screw with cap come with the caliper

    Quick facts

    • Part: Nugeon 99-01627A brake caliper
    • Also called: disc brake caliper
    • Fits: 2001-2003 Toyota Highlander
    • Position: Rear right
    • Material: Cast iron
    • Condition: Remanufactured

    A sticking or leaking disc brake caliper can show up as the vehicle pulling to one side, a burning smell after driving or one pad wearing faster than the other. Those signs can have other causes, so during a brake service, with the engine off and cool, look for fluid around the dust boot before replacing the caliper. Calipers are normally replaced in pairs, one on each side of the axle, but this listing is the rear right only; the rear left is ordered separately.

    Fits

    This is a direct-fit brake caliper for the 2001-2003 Toyota Highlander.

    Specifications

    Fit and size

    • Position: Rear right
    • Quantity per listing: 1
    • Piston diameter: 38 mm (1.5 in)
    • Inlet thread size: M10 - 1.0
    • Bleeder screw thread: M7-1.0
    • Cast numbers: housing 38 L, bracket 40

    Build and materials

    • Caliper type: Floating
    • Condition: Remanufactured
    • Housing material: Cast iron
    • Piston material: Steel
    • Finish: Rust preventative
    • Inlet fitting: Banjo bolt
    • Country of origin: Mexico

    In the box

    One caliper with its pad hardware and crush washer(s). Brake pads, anti-squeal shims, wear sensors and the bracket mounting bolts are not included, so plan on new bolts.

    Interchange / FMSI:

    FMSI: D885

    Frequently Asked Questions

    Is this the right brake caliper replacement for the 2001-2003 Toyota Highlander?

    Yes. Nugeon 99-01627A is the rear right caliper for the 2001-2003 Toyota Highlander; the rear left is a separate part.

    Does this rear caliper come with the bracket and slides?

    Yes. It comes with the bracket, caliper slides, pad hardware, dust boots and a bleeder screw with cap. Brake pads and bracket mounting bolts are not included.

    What are the piston size and hose connection on this floating caliper?

    Nugeon 99-01627A has a single 38 mm steel piston, an M10 - 1.0 banjo bolt inlet and an M7-1.0 bleeder screw.

    How do I tell whether a rear brake caliper is sticking?

    Signs can include the vehicle pulling to one side, a burning smell after driving, or one pad wearing much faster than the other. A shop can test the brake hydraulics.

    Is this Nugeon caliper remanufactured, and where is it made?

    Yes, it is a remanufactured caliper with a cast iron housing. Its country of origin is Mexico.

    Reviews

    No reviews yet — be the first to review this product.

    Write a Review