Front Left Lower Control Arm with Ball Joint for 2019-2025 Toyota RAV4 & More - Mevotech Supreme CMS861312

$107.99

Vehicles this part fits

    Part number: CMS861312
    UPC: 677319505009
    Condition: New
    Weight: 17.71 LBS
    Sold as: 1 per listing
    $107.99
    Adding to cart… The item has been added

    Have questions?

    Mevotech Supreme Suspension Control Arm and Ball Joint Assembly P/N:CMS861312
    Mevotech Supreme Suspension Control Arm and Ball Joint Assembly P/N:CMS861312
    $107.99
    $107.99

    Mevotech Supreme CMS861312 front left lower control arm with ball joint for the 2019-2025 Toyota RAV4 and other vehicles links the wheel assembly to the vehicle and pivots on its ball joint. This Mevotech Supreme suspension control arm, also sold as a control arm and ball joint assembly, comes with its bushings, ball joint and dust boot.

    • Mevotech Supreme control arm engineered in-house with application-specific upgrades for durability and performance
    • Double-bonded rubber bushings for increased stiffness and durability
    • Sintered metal bearing for longer-lasting performance
    • Neoprene dust boot built into the ball joint assembly to seal out corrosion
    • Application-specific ball stud system with a larger sphere
    • 180 degree SAE grease fitting included for servicing

    Quick facts

    • Part: Mevotech Supreme CMS861312 control arm with ball joint
    • Also called: control arm and ball joint assembly
    • Fits: 2019-2025 Toyota RAV4 and other vehicles
    • Position: Front left lower
    • Material: Steel
    • Condition: New

    A clunk over bumps, a loose steering feel or uneven tire wear can come from a worn arm, ball joint or bushing, though other worn suspension parts can give similar symptoms. With the engine off, look the arm over for cracked bushings or a torn boot to find the cause before you replace anything.

    Fits

    This direct-fit replacement also fits the 2023-2025 Toyota Crown and the 2025 Toyota Crown Signia. If your car is not named here, run it through the "Vehicles it fits" section. This listing is one arm for the front left, which takes one; the front right is a separate part, and the two sides are normally replaced together.

    Specifications

    Fit and size

    • Position: front left lower
    • Quantity: 1 per listing
    • Maximum width: 14.21 in
    • Maximum length: 14.11 in
    • Ball joint mounting type: bolt in
    • Ball joint stud type: threaded

    Build and materials

    • Construction: stamped steel
    • Control arm material: steel
    • Bushing material: rubber
    • Bearing material: sintered metal
    • Dust boot material: neoprene
    • Condition: new
    • Country of origin: China

    In the box

    One front left lower control arm with the ball joint, bushings, dust boot, grease fitting, castle nut and cotter pin.

    Installation notes

    • The ball joint secures to the vehicle with the part-specific castle nut and cotter pin supplied.
    • The ball joint arrives pre-greased.
    • Labor Saver designs, tools and hardware are meant to make installation faster and easier.

    Interchange: 19531515 · CA75323 · 2609614 · 4333009A80 · 4333009A90 · 4333049225 · 480690R050 · 4806942070

    Product information is for general reference and may contain errors. See our Disclaimer.

    This part cross-references / interchanges with the following part numbers:

    19531515, CA75323, CMS861312, 2609614, 4333009A80, 4333009A90, 4333049225, 480690R050, 4806942070

    Frequently Asked Questions

    Is this RAV4 control arm the front left one for a 2019-2025 Toyota RAV4?

    Yes, Mevotech Supreme CMS861312 is the front left lower control arm with ball joint for the 2019-2025 Toyota RAV4. The front right side is a separate part.

    Does this RAV4 lower control arm also fit the 2023-2025 Toyota Crown or the 2025 Toyota Crown Signia?

    Yes, Mevotech Supreme CMS861312 fits the 2023-2025 Toyota Crown and the 2025 Toyota Crown Signia in the same front left lower position.

    Does this control arm come with the ball joint and bushings already in it?

    Yes. The assembly includes the ball joint, rubber bushings and neoprene dust boot, plus the castle nut, cotter pin and grease fitting.

    What are the bushings and bearing in this Mevotech control arm made of?

    The bushings are rubber and double bonded for stiffness. The ball joint bearing is sintered metal, and the control arm is stamped steel.

    Is the ball joint on this arm pre-greased, and can it be serviced later?

    Yes. The ball joint comes pre-greased and has a 180 degree SAE grease fitting included for later servicing.

    Reviews

    No reviews yet — be the first to review this product.

    Write a Review