MOOG Chassis Products Suspension Control Arm and Ball Joint Assembly P/N:RK623000
$212.99
(You save)
Tighten up loose steering and quiet front-end clunks with the MOOG Chassis Front Right Lower Suspension Control Arm and Ball Joint Assembly RK623000 — a direct-fit Ford Fusion control arm that installs in the front right lower position on the listed applications. This one-piece control arm and ball joint assembly drops into the 2013-2020 Ford Fusion, 2019-2020 Ford Police Responder Hybrid, 2019-2020 Ford SSV Plug-In Hybrid, and 2013-2020 Lincoln MKZ. If a worn arm, bushing, or ball joint is behind your steering slop, this is a clean 2013 Ford Fusion control arm replacement.
Carbon fiber-reinforced bearing: paired with induction-hardened studs to reduce socket friction versus non-reinforced bearings for longer socket life.
Greaseable socket: lets you flush contaminants with fresh lubricant to reduce corrosion and wear.
Pre-installed dust boot seal: forms a barrier against wear-causing dirt and water; premium pre-installed bushings are tuned for stiffness that helps inhibit noise.
Hardware included: comes with the necessary hardware, with precision tolerances intended for easy installation and steering alignment.
Studs are induction hardened to resist breakage and improve fatigue life, and laser-etched ID marks genuine MOOG quality. A common 2016 Ford Fusion lower control arm fit.
It's a one-piece front suspension arm with an integrated ball joint that locates the wheel, pivots on bushings, and lets the wheel steer and travel. Replacing the assembly renews the arm, bushings, and joint together.
Does the MOOG RK623000 fit my Ford Fusion?
It's cataloged as the front right lower unit for the 2013-2020 Ford Fusion, 2019-2020 Ford Police Responder Hybrid, 2019-2020 Ford SSV Plug-In Hybrid, and 2013-2020 Lincoln MKZ. See the Buyer's Guide tab to confirm fitment.
Does this control arm come with hardware?
Yes. Per MOOG, it comes with the necessary hardware for installation. Consult the vehicle service information for correct torque specs and whether any fasteners are single-use.
What are signs my control arm or ball joint may need replacing?
Clunking or knocking over bumps, loose or wandering steering, and uneven tire wear can be signs. Diagnose the cause first, since these symptoms can have other sources.
Is the ball joint greaseable?
Yes. The socket is greaseable, so you can add fresh lubricant to flush out contaminants and help reduce corrosion and wear during maintenance.
Write a Review
MOOG
MOOG Chassis Products Suspension Control Arm and Ball Joint Assembly P/N:RK623000
MOOG RK623419 Rear Left Upper Suspension Control Arm and Ball Joint Assembly for Nissan MaximaRear Left Upper Suspension Control Arm and Ball Joint AssemblyMOOG premium control arms for foreign and...
MOOG RK623281 Front Left Lower Suspension Control Arm and Ball Joint Assembly for Kia SorentoFront Left Lower Suspension Control Arm and Ball Joint AssemblyMOOG premium control arms for foreign and...
MOOG RK623383 Front Right Lower Suspension Control Arm and Ball Joint Assembly for Cadillac CTSFront Right Lower Suspension Control Arm and Ball Joint AssemblyMOOG premium control arms for foreign...
MOOG RK623294 Front Right Lower Rearward Suspension Control Arm and Ball Joint Assembly for Mercedes-Benz S550Front Right Lower Rearward Suspension Control Arm and Ball Joint AssemblyMOOG premium...
MOOG RK643453 Front Left Lower Suspension Control Arm and Ball Joint Assembly for Hyundai TucsonFront Left Lower Suspension Control Arm and Ball Joint AssemblyMOOG premium control arms for foreign...
WARNING:
These products can expose you to chemicals including lead and phthalates, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
