Delphi Suspension Stabilizer Bar Bushing Kit P/N:TD4193W
$19.99
(You save)
Silence a clunking, rattling front sway bar and keep it firmly located with the Delphi Suspension Stabilizer Bar Bushing Kit TD4193W. This front stabilizer bar bushing kit drops in as a direct-fit replacement across a wide run of trucks and SUVs — including the 1994-2010 Dodge Ram 1500, 2500 and 3500, the 1997-2013 Jeep Wrangler, the 1997-2005 Dodge Dakota, the 1999-2003 Dodge Durango and the 2011-2013 Ram 1500. See the Buyer's Guide tab for the full list of covered vehicles.
The bushings cushion the front stabilizer bar where it mounts to the chassis, letting the bar rotate as it works to limit body roll while damping road noise. If worn or cracked front bushings are the cause of a clunk, rattle or sloppy handling, this kit replaces them.
Designed to OE standards: Delphi applies its OE expertise and extensive dimensional and material analysis for close compatibility between the OE and aftermarket part.
Tested to the extreme: the parts withstand temperatures below -40°C and over 120°C and endure 720 hours of salt spray.
Quieter, consistent performance: manufactured to reduce noise and for consistent service life.
Smoother ride: the bushings assist in restoring the vehicle's smooth ride.
What does the Delphi TD4193W sway bar bushing kit do?
It replaces the worn bushings that cushion and locate the front stabilizer bar where it mounts to the chassis, letting the bar work to control body roll while helping to reduce noise and slop.
Which vehicles does this kit fit?
It's a direct-fit for applications such as the 1994-2010 Dodge Ram 1500/2500/3500, 1997-2013 Jeep Wrangler, 1997-2005 Dodge Dakota, 1999-2003 Dodge Durango and 2011-2013 Ram 1500. See the Buyer's Guide tab.
Is this a front or rear kit?
It is cataloged for the FRONT sway bar on the listed applications, so it replaces the bushings on the front stabilizer bar.
What are the signs my sway bar bushings need replacing?
Common signs include clunking, rattling or knocking from the front suspension over bumps and during cornering, plus looser handling. Diagnose the cause first, as other suspension parts can make similar noises.
How are Delphi bushings tested?
Delphi tests to OE performance: the parts withstand temperatures below -40°C and above 120°C and endure 720 hours of salt spray, backed by dimensional and material analysis for OE compatibility.
Write a Review
Delphi
Delphi Suspension Stabilizer Bar Bushing Kit P/N:TD4193W
Quiet a clunking rear sway bar and keep it located under hard cornering with the Delphi Suspension Stabilizer Bar Bushing Kit (P/N: TD4177W). This kit cushions the rear stabilizer bar where it mounts...
Keep the rear stabilizer bar located and quiet with the Delphi Suspension Stabilizer Bar Bushing Kit (TD5070W). These bushings secure the rear stabilizer bar to the frame, cushioning it against the...
Quiet a clunking, knocking rear sway bar and keep the stabilizer bar located properly with the Delphi Suspension Stabilizer Bar Bushing Kit (TD996W). This rear sway bar bushing kit cushions the bar...
Quiet a clunking, rattling front sway bar and help keep your Mercedes-Benz cornering flat with the Delphi Suspension Stabilizer Bar Bushing Kit TD5885W. This front-to-frame stabilizer bar bushing kit...
Quiet a clunking front sway bar and keep the stabilizer bar located where it belongs with the Delphi Suspension Stabilizer Bar Bushing Kit TD671W. These front stabilizer bar bushings cushion the bar...
WARNING:
These products can expose you to chemicals including lead and phthalates, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
