Delphi Suspension Stabilizer Bar Bushing Kit P/N:TD1202W
$43.99
(You save)
Quiet a clunking, rolling front end and keep the front stabilizer bar located precisely with the Delphi Suspension Stabilizer Bar Bushing Kit TD1202W. This front sway bar bushing kit is a direct-fit replacement for the 2003-2008 Subaru Forester, 2002-2007 Subaru Impreza, 2000-2004 Subaru Outback, 2003-2006 Subaru Baja, and 1996-2004 Subaru Legacy — see the Buyer's Guide tab for engine-level fitment. The bushings cushion the front stabilizer bar where it mounts to the chassis, letting the bar resist body roll while isolating road noise and vibration.
Built to OE standards: Delphi bushings are designed to OE standards, drawing on the same OE engineering fitted to millions of vehicles worldwide.
Consistent service life: manufactured for consistent life, with validation that includes exposure below -40°C, above 120°C, and 720 hours of salt spray.
Quieter operation: manufactured to reduce noise so the bar operates without squeak or rattle.
Smooth ride: designed to assist in restoring the smooth ride of the vehicle.
Worn or cracked stabilizer bar bushings can allow front-end clunking over bumps, extra body sway in corners, and a loose feel — signs these bushings may need replacing. Diagnose the cause before replacing.
It is the Delphi TD1202W Suspension Stabilizer Bar Bushing Kit — a front sway bar bushing kit that cushions and locates the front stabilizer bar at its chassis mounts.
Which vehicles does the TD1202W fit?
It is a direct-fit replacement for the 2003-2008 Subaru Forester, 2002-2007 Subaru Impreza, 2000-2004 Subaru Outback, 2003-2006 Subaru Baja, and 1996-2004 Subaru Legacy. See the Buyer's Guide tab for full details.
Is this a front or rear bushing kit?
This kit is for the front stabilizer bar position on the listed Subaru applications.
What are the signs my stabilizer bar bushings may need replacing?
Front-end clunking over bumps, increased body roll in corners, and a loose or vague feel can indicate worn or cracked bushings. Diagnose the cause before replacing.
How are Delphi bushings tested?
Delphi bushings are designed to OE standards and validated through dimensional and material analysis, including exposure below -40°C, above 120°C, and 720 hours of salt spray.
Write a Review
Delphi
Delphi Suspension Stabilizer Bar Bushing Kit P/N:TD1202W
Quiet a clunking rear sway bar and keep it located under hard cornering with the Delphi Suspension Stabilizer Bar Bushing Kit (P/N: TD4177W). This kit cushions the rear stabilizer bar where it mounts...
Keep the rear stabilizer bar located and quiet with the Delphi Suspension Stabilizer Bar Bushing Kit (TD5070W). These bushings secure the rear stabilizer bar to the frame, cushioning it against the...
Quiet a clunking, rattling front sway bar and help keep your Mercedes-Benz cornering flat with the Delphi Suspension Stabilizer Bar Bushing Kit TD5885W. This front-to-frame stabilizer bar bushing kit...
Quiet a clunking front sway bar and keep the stabilizer bar located where it belongs with the Delphi Suspension Stabilizer Bar Bushing Kit TD671W. These front stabilizer bar bushings cushion the bar...
Quiet a clunking front sway bar and keep the stabilizer bar properly located with the Delphi Suspension Stabilizer Bar Bushing Kit (TD994W). It drops in as a direct-fit replacement for the front...
WARNING:
These products can expose you to chemicals including lead and phthalates, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
