Delphi Suspension Stabilizer Bar Bushing Kit P/N:TD1676W
$10.99
(You save)
Quiet a clunking, rattling front stabilizer bar and keep it located to the frame with the Delphi Suspension Stabilizer Bar Bushing Kit (MPN TD1676W). This stabilizer bar bushing kit mounts in the FRONT TO FRAME position, cushioning the sway bar where it clamps to the chassis so the bar can resist body roll while limiting metal-to-metal noise. It fits the 2007-2012 Hyundai Santa Fe, 2006-2010 Hyundai Sonata, 2009-2012 Hyundai Genesis, 2010-2012 Hyundai Genesis Coupe, 2007-2010 Hyundai Entourage, 2011-2013 Kia Sorento, 2007-2009 Kia Amanti, and 2006-2012 Kia Sedona — see the Buyer's Guide tab for the full list and engine details.
Built to OE standards: Delphi applies its OE steering and suspension expertise to this aftermarket kit, with dimensional and material analysis for close compatibility between the OE and aftermarket part.
Validated to the extreme: Delphi parts withstand temperatures below -40°C and over 120°C and are exposed to 720 hours of salt spray.
Manufactured for consistent life and to reduce noise from the stabilizer bar mounting.
Helps restore the smooth ride of the vehicle when worn bushings are the cause.
It cushions the stabilizer (sway) bar where it mounts to the frame, letting the bar resist body roll while limiting metal-to-metal noise and helping locate the bar.
Where does this kit mount?
This Delphi kit (TD1676W) mounts in the FRONT TO FRAME position, at the points where the front stabilizer bar clamps to the chassis.
Which vehicles does TD1676W fit?
It fits the 2007-2012 Santa Fe, 2006-2010 Sonata, 2009-2012 Genesis, 2010-2012 Genesis Coupe, 2007-2010 Entourage, 2011-2013 Sorento, 2007-2009 Amanti, and 2006-2012 Sedona. See the Buyer's Guide.
What are the signs these bushings may need replacing?
Clunking or rattling from the front over uneven roads, increased body roll in turns, and worn or deteriorated bushings at the stabilizer bar mounts can all be signs replacement may be needed.
Is this built to OE standards?
Yes. Delphi designs these bushings to OE standards and uses dimensional and material analysis for close compatibility, with validation across extreme temperatures and 720 hours of salt spray.
Write a Review
Delphi
Delphi Suspension Stabilizer Bar Bushing Kit P/N:TD1676W
Quiet a clunking rear sway bar and keep it located under hard cornering with the Delphi Suspension Stabilizer Bar Bushing Kit (P/N: TD4177W). This kit cushions the rear stabilizer bar where it mounts...
Keep the rear stabilizer bar located and quiet with the Delphi Suspension Stabilizer Bar Bushing Kit (TD5070W). These bushings secure the rear stabilizer bar to the frame, cushioning it against the...
Quiet a clunking, rattling front sway bar and help keep your Mercedes-Benz cornering flat with the Delphi Suspension Stabilizer Bar Bushing Kit TD5885W. This front-to-frame stabilizer bar bushing kit...
Quiet a clunking front sway bar and keep the stabilizer bar located where it belongs with the Delphi Suspension Stabilizer Bar Bushing Kit TD671W. These front stabilizer bar bushings cushion the bar...
Quiet a clunking front sway bar and keep the stabilizer bar properly located with the Delphi Suspension Stabilizer Bar Bushing Kit (TD994W). It drops in as a direct-fit replacement for the front...
WARNING:
These products can expose you to chemicals including lead and phthalates, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
