Delphi Suspension Stabilizer Bar Bushing Kit P/N:TD4167W
$14.99
(You save)
Quiet a clunking front stabilizer bar and keep it properly located to the frame with the Delphi Suspension Stabilizer Bar Bushing Kit TD4167W. This sway bar bushing kit drops in as a direct-fit replacement for the 2004-2009 Chevrolet Trailblazer, 2004-2009 GMC Envoy, 2004-2008 Isuzu Ascender, 2004-2007 Buick Rainier and the 2004 Oldsmobile Bravada. These are the FRONT, front-to-frame stabilizer bar bushings that cushion the sway bar and hold it against the frame so the bar can control body roll through corners.
Designed to OE standards: Delphi builds these bushings to OE standards, drawing on the OE steering and suspension expertise applied across its aftermarket portfolio.
Built for consistent life and quieter operation: manufactured for consistent life and to reduce noise.
Validated to extremes: tested at temperatures below -40°C and over 120°C and exposed to 720 hours of salt spray, with dimensional and material analysis for close OE-to-aftermarket compatibility.
Smoother ride: designed to help restore the vehicle's smooth ride.
Worn stabilizer bar bushings can allow clunking or rattling over bumps and extra body lean in turns; if the old bushings are the cause, this kit replaces them.
It replaces the front stabilizer bar bushings that cushion the sway bar and hold it to the frame, letting the bar control body roll through turns.
Which vehicles does the TD4167W fit?
It fits the 2004-2009 Chevrolet Trailblazer, 2004-2009 GMC Envoy, 2004-2008 Isuzu Ascender, 2004-2007 Buick Rainier and 2004 Oldsmobile Bravada. See the Buyer's Guide tab to confirm your vehicle.
Is this a front or rear kit?
It is the FRONT kit. These bushings mount the front stabilizer bar to the frame (front-to-frame position).
What are the signs my stabilizer bar bushings need replacing?
Clunking or rattling over bumps and increased body lean in turns can be signs of worn bushings. Diagnose the cause first, since other suspension parts can produce similar symptoms.
How is this kit built for durability?
Delphi builds these bushings to OE standards and tests them below -40°C, over 120°C and through 720 hours of salt spray, with dimensional and material analysis for close OE compatibility.
Write a Review
Delphi
Delphi Suspension Stabilizer Bar Bushing Kit P/N:TD4167W
Quiet a clunking rear sway bar and keep it located under hard cornering with the Delphi Suspension Stabilizer Bar Bushing Kit (P/N: TD4177W). This kit cushions the rear stabilizer bar where it mounts...
Keep the rear stabilizer bar located and quiet with the Delphi Suspension Stabilizer Bar Bushing Kit (TD5070W). These bushings secure the rear stabilizer bar to the frame, cushioning it against the...
Quiet a clunking, knocking rear sway bar and keep the stabilizer bar located properly with the Delphi Suspension Stabilizer Bar Bushing Kit (TD996W). This rear sway bar bushing kit cushions the bar...
Quiet a clunking, rattling front sway bar and help keep your Mercedes-Benz cornering flat with the Delphi Suspension Stabilizer Bar Bushing Kit TD5885W. This front-to-frame stabilizer bar bushing kit...
Quiet a clunking front sway bar and keep the stabilizer bar located where it belongs with the Delphi Suspension Stabilizer Bar Bushing Kit TD671W. These front stabilizer bar bushings cushion the bar...
WARNING:
These products can expose you to chemicals including lead and phthalates, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
