Rear Brake Hydraulic Hose for 1997-1999 Mitsubishi Montero Sport & More - Dorman H38441

$14.99

Vehicles this part fits

    Part number: H38441
    UPC: 082702370810
    Condition: New
    Weight: 0.30 LBS
    Item Package Quantity: 1
    $14.99
    Adding to cart… The item has been added

    Have questions?

    Dorman - First Stop Brake Hydraulic Hose P/N:H38441
    Dorman - First Stop Brake Hydraulic Hose P/N:H38441
    $14.99
    $14.99

    Dorman H38441 rear brake hydraulic hose for the 1997-1999 Mitsubishi Montero Sport and other vehicles carries brake fluid through the flexible part of the rear brake circuit. This Dorman brake hydraulic hose is engineered to match the performance of the original brake hose on specific vehicles.

    • Position-specific, made to precise measurements for an exact fit
    • Materials tested to government-regulated safety and durability standards
    • EPDM rubber hose with specially coated, corrosion-resistant fittings
    • DOT approved flexible hose, 13.25 inches overall length

    Quick facts

    • Part: Dorman H38441 brake hydraulic hose
    • Fits: the 1997-1999 Mitsubishi Montero Sport and other vehicles
    • Position: rear right, rear left, rear center, rear left outer, rear right outer
    • Material: EPDM rubber hose, treated steel fittings
    • Condition: New

    A soft pedal, fluid at a hose end, or cracked or bulging rubber can mean a brake hose is worn. These signs alone do not prove the hose is at fault, since a leaking caliper or wheel cylinder can leave fluid in the same area. Have any brake leak looked at promptly.

    Fits

    This hose is listed for a wide range of Mitsubishi and Dodge models, led by the 1997-1999 Mitsubishi Montero Sport, the 1983-1996 Mitsubishi Mighty Max and the 1987-1993 Dodge Ram 50. The 1997-1999 Mitsubishi Montero Sport takes one. This listing is one hose, and the other side of the same axle is normally done at the same time. To see whether your own model and engine are covered, open the "Vehicles it fits" section.

    Specifications

    Fit and size

    • Position: rear right, rear left, rear center, rear left outer, rear right outer
    • Quantity per application: 1
    • Overall length: 13.25 in
    • End 1 thread size: 10 mm
    • End 2 fitting inside diameter: M10 x 1.0
    • End 1 and end 2 fitting type: female

    Build and materials

    • Type: flexible hose
    • Hose material: EPDM rubber
    • Outer sleeve material: rubber
    • Fitting material (both ends): treated steel
    • DOT approved: yes
    • Condition: New
    • Country of origin: China

    In the box

    One brake hose. Mounting hardware, a bracket, a gasket or seal and a jacket are not included, and any old hardware may not be reusable, so plan on new pieces.

    Interchange: 87-16027 · 87-16054 · HB-52027 · HB-52054 · 150.46027 · 350-72016
    18J498 · B917306 · 610592 · 77782 · BH250450 · MB277096 · MB857581 · MR129795 · NF38441 · BH38441 · 2202418 · BH107288 · F107288

    Product information is for general reference and may contain errors. See our Disclaimer.

    This part cross-references / interchanges with the following part numbers:

    18J498, 87-16027, 87-16054, B917306, 610592, HB-52027, HB-52054, 77782, 150.46027, BH250450, 350-72016, MB277096, MB857581, MR129795, NF38441, BH38441, 2202418, BH107288, F107288

    Frequently Asked Questions

    Does the Dorman H38441 brake hose fit the 1997-1999 Mitsubishi Montero Sport?

    Yes. Dorman H38441 is a rear brake hydraulic hose for the 1997-1999 Mitsubishi Montero Sport, and that vehicle takes one.

    Does the Dorman H38441 hose come with a bracket or gasket?

    No. Dorman H38441 comes as one brake hose only. The bracket, mounting hardware, gasket or seal and jacket are not included, so plan on new hardware.

    What are the hose and fittings made of on this brake hydraulic hose?

    The hose is EPDM rubber with a rubber outer sleeve. Both end fittings are treated steel with a corrosion-resistant coating, and the hose is DOT approved.

    How long is this rear brake hose and what thread sizes does it use?

    Overall length is 13.25 inches. End 1 has a 10 mm thread size and end 2 is M10 x 1.0, and both ends are female fittings.

    Can a bulging or cracked rubber section on a brake hose mean it needs replacing?

    Yes. Bulging, cracked or weeping rubber can mean the hose is worn out. Have the brakes checked promptly rather than driving on it.

    Reviews

    No reviews yet — be the first to review this product.

    Write a Review