Front Lower Ball Joint for 2012-2014 Dodge I10 - Dorman 539-809

$37.99

Vehicles this part fits

    Part number: 539-809
    UPC: 194883751101
    Condition: New
    Weight: 2.00 LBS
    Item Package Quantity: 1
    $37.99
    Adding to cart… The item has been added

    Have questions?

    Dorman - OE Solutions Suspension Ball Joint P/N:539-809
    Dorman - OE Solutions Suspension Ball Joint P/N:539-809
    $37.99
    $37.99

    Dorman 539-809 front lower ball joint for the 2012-2014 Dodge I10 works as the pivot between the control arm and steering knuckle. This Dorman ball joint, also called a suspension ball joint, replaces only the failed joint, not the complete assembly.

    • Steel construction with a polymer bearing
    • Polychloroprene dust boot included
    • Threaded tapered stud with 15.97 mm thread diameter and 1.5 mm pitch
    • Press-in housing with a 40.15 mm press-fit diameter
    • Part of the Dorman OE Solutions line

    Quick facts

    • Part: Dorman 539-809 ball joint
    • Also called: suspension ball joint
    • Fits: 2012-2014 Dodge I10
    • Position: Front lower
    • Material: Steel
    • Condition: New

    A worn ball joint can show up as a clunk over bumps, loose or wandering steering, or uneven tire wear. Worn control arm bushings, tie rod ends or a wheel bearing can be behind those signs too, so find the cause before you buy.

    Fits

    It is a direct replacement for the 2012-2014 Dodge I10. This listing is one ball joint; the other side of the front axle is normally done at the same time.

    Specifications

    Fit and size

    • Position: front lower
    • Quantity per vehicle: 2
    • Stud tapered end 1 diameter: 27.2 mm
    • Stud tapered end 2 diameter: 22 mm
    • Stud taper per foot: 2 in
    • Stud thread: 15.97 mm diameter, 1.5 mm pitch, 35.5 mm long
    • Maximum outside diameter: 61 mm
    • Housing press-fit diameter: 40.15 mm
    • Wrench size: 12 mm

    Build and materials

    • Material: steel
    • Bearing material: polymer
    • Dust boot material: polychloroprene
    • Mounting type: press-in
    • Stud: tapered, pinch type
    • Greaseable: no
    • Condition: new
    • Country of origin: Turkey

    In the box

    One ball joint with its dust boot and a nut. This listing holds one ball joint, and the 2012-2014 Dodge I10 takes two. Mounting hardware, washers, a castle nut, a cotter pin and a grease fitting are not included; the old fasteners may not be reusable, so plan on new ones.

    Installation notes

    • A ball joint press tool is normally required for installation.

    Interchange: 5453007000 · 545300X000 · K500277 · 1006025

    Product information is for general reference and may contain errors. See our Disclaimer.

    This part cross-references / interchanges with the following part numbers:

    5453007000, 545300X000, K500277, 1006025

    Frequently Asked Questions

    Is this ball joint right for the 2012-2014 Dodge I10?

    Yes. Dorman 539-809 is a front lower ball joint made for the 2012-2014 Dodge I10, and the car takes two of them.

    Does this ball joint come with a dust boot and nut?

    Yes. The listing is one ball joint with its polychloroprene dust boot and a nut. Mounting hardware, washers, a castle nut, a cotter pin and a grease fitting are not included.

    What stud thread and taper does Dorman 539-809 have?

    The stud thread is 15.97 mm in diameter with a 1.5 mm pitch and 35.5 mm of thread length. The tapered stud measures 27.2 mm at one end and 22 mm at the other.

    Do I need a special tool to install this ball joint?

    A ball joint press tool is normally required for installation, because the ball joint housing is a press-in fit with a 40.15 mm press-fit diameter.

    Is this front lower ball joint greaseable?

    No. This ball joint is not greaseable and comes without a grease fitting.

    Reviews

    No reviews yet — be the first to review this product.

    Write a Review