Heater Hose for 2011-2014 Honda Fit & More - Gates 18392

$8.99

Vehicles this part fits

    Part number: 18392
    UPC: 770075531722
    Condition: New
    Weight: 0.07 LBS
    Item Package Quantity: 1
    $8.99
    Adding to cart… The item has been added

    Have questions?

    Gates HVAC Heater Hose P/N:18392
    Gates HVAC Heater Hose P/N:18392
    $8.99
    $8.99

    Gates 18392 heater hose for the 2011-2014 Honda Fit 4-cylinder 1.5L and other vehicles carries coolant between the throttle body and the pipe.

    • Gates Small I.D. Molded Coolant Hose, factory-molded for smaller, tighter engine compartments
    • EPDM tube and EPDM cover with synthetic fiber knit reinforcement
    • Engineered to resist electrochemical degradation, a leading cause of hose failure
    • Meets SAE 20R3 Type EC Class D-1 and D-2
    • Temperature range of -40°F to 275°F (-40°C to 135°C)
    • Used for coolant, water and air, and approved for marine applications

    Quick facts

    • Part: Gates 18392 heater hose
    • Also called: HVAC heater hose
    • Fits: 2011-2014 Honda Fit 4-cylinder 1.5L and other vehicles
    • Position: Throttle body to pipe
    • Material: EPDM
    • Condition: New

    A worn heater hose can show up as coolant dripping or dampness at the hose, cracks, a soft or swollen feel, or a heater that is slow to warm up. Before you replace this hose, rule out a loose clamp or a leaking fitting elsewhere in the heater circuit, because a drip or low coolant has more than one possible source.

    Fits

    This hose fits the 2011-2014 Honda Fit 4-cylinder 1.5L and the 2011-2014 Honda City 4-cylinder 1.5L. It runs from the throttle body to the pipe, and the engine takes one hose at that spot.

    Specifications

    Fit and size

    • Position: Throttle body to pipe
    • Quantity per vehicle: 1
    • Inside diameter, both ends: 7 mm (0.29 in)
    • Centerline length: 130 mm (5.1 in)

    Build and materials

    • Material: EPDM tube and EPDM cover
    • Reinforcement: synthetic fiber knit
    • Construction: molded
    • Temperature range: -40°F to 275°F (-40°C to 135°C)
    • Standard: SAE 20R3 Type EC Class D-1 and D-2
    • Condition: New
    • Country of origin: United States

    Installation notes

    • Replace the hose clamps each time a new coolant hose is installed.
    • Not for fuel or oil transfer applications.

    Interchange: 14668S · F10747 · 19527RB0000 · 10392

    Product information is for general reference and may contain errors. See our Disclaimer.

    This part cross-references / interchanges with the following part numbers:

    14668S, 18392, F10747, 19527RB0000, 10392

    Frequently Asked Questions

    Is the Gates 18392 heater hose right for the 2011-2014 Honda City 4-cylinder 1.5L?

    Yes. Gates 18392 fits the 2011-2014 Honda City 4-cylinder 1.5L and the 2011-2014 Honda Fit 4-cylinder 1.5L, with one hose per car at the throttle body to pipe position.

    Can the Gates heater hose be used on fuel or oil lines?

    No. Gates 18392 is made for coolant, water and air, and it is not for fuel or oil transfer applications.

    Is the Gates molded heater hose approved for marine use?

    Yes. This molded hose can be used for coolant, water and air applications and is also approved for marine applications.

    What can a worn HVAC heater hose look like?

    With the engine off and cool, look for cracks, a soft or swollen hose, or coolant dampness at the ends. If you are unsure what you see, a shop can test the cooling system.

    Should I replace the clamps when I install the Gates 18392?

    Yes. Replace the hose clamps each time a new coolant hose is installed, including this Gates 18392 heater hose.

    Reviews

    No reviews yet — be the first to review this product.

    Write a Review