Front Right CV Axle for 1991-2000 Nissan Sentra & More - A1 CARDONE 66-6162

$101.99

Vehicles this part fits

    Part number: 66-6162
    UPC: 082617634472
    Condition: New
    Weight: 20.00 LBS
    Item Package Quantity: 1
    $101.99
    Adding to cart… The item has been added

    Have questions?

    CARDONE New CV Axle Assembly P/N:66-6162
    CARDONE New CV Axle Assembly P/N:66-6162
    $101.99
    $101.99

    A1 CARDONE 66-6162 front right CV axle for the 1991-2000 Nissan Sentra and other vehicles sends drive torque from the transaxle to the front right wheel. This CV axle assembly is engineered to avoid the repeat failures that affect original axles.

    • Neoprene boots with additional bellows where needed, to resist bellow stress and cracking, the leading cause of boot failure
    • Each shaft is individually verified for straightness, for vibration-free performance at all speeds
    • Boot clamps are pneumatically crimped to seal the boot to the housing
    • Grease that withstands high-temperature and high-torque demands
    • Precision-rolled splines and threads for proper fit in the hub and transmission and for the axle nut
    • Transmission seal diameter is precision-machined after heat treatment for a surface finish that promotes long seal life

    Quick facts

    • Part: A1 CARDONE 66-6162 CV axle
    • Also called: CV axle assembly
    • Fits: the 1991-2000 Nissan Sentra and other vehicles
    • Position: Front right
    • Material: Steel shaft, neoprene boots
    • Condition: New

    Loud clicking when you turn under power, a thump with vibration on acceleration, or grease around a torn boot can mean the axle is wearing out. These signs alone do not prove the axle is the problem, because a worn wheel bearing can make a similar noise.

    Fits

    This axle is listed for a wide range of Nissan models, such as the 1991-2000 Nissan Sentra, the 1998-2000 Nissan Lucino and the 1995-1998 Nissan 200SX, and is built to meet O.E. form, fit and function. Open the "Vehicles it fits" section to check your exact model and engine. The car takes one axle on each side; this listing is the front right, and the front left is ordered separately.

    Specifications

    Fit and size

    • Position: Front right
    • Quantity per vehicle: 1 for this side
    • Shaft diameter: 27 mm (1.063 in)
    • Compressed length: 908.05 mm (35.75 in)
    • Inboard joint: splined, 25 splines
    • Outboard joint: splined, 25 splines
    • Axle nut: hex, M22x1.5 thread, 32 mm socket, 18 mm long

    Build and materials

    • Type: complete axle with CV joints
    • Shaft material: steel
    • Boot material: neoprene, 3 ribs
    • ABS tone ring: included, toothed, 42 teeth
    • Condition: New
    • Country of origin: China

    In the box

    One complete axle with CV joints, a new axle nut and an instruction sheet.

    Installation notes

    • Use a torque wrench on the axle nut and tighten it to the manufacturer's specification; never use an impact wrench.
    • Remove and install one CV axle at a time.
    • Install new transaxle seals to avoid leaking.
    • Use a press-type tool to remove the old stub shaft; never strike it with a hammer.

    Interchange: 391000M600 · 391000M605 · 391000M610 · 391000M615 · 3910060Y00 · 3910060Y05 · 3910060Y10 · 3910060Y15 · 3910164Y00

    Product information is for general reference and may contain errors. See our Disclaimer.

    This part cross-references / interchanges with the following part numbers:

    391000M600, 391000M605, 391000M610, 391000M615, 3910060Y00, 3910060Y05, 3910060Y10, 3910060Y15, 3910164Y00

    Frequently Asked Questions

    Will this front right CV axle fit the 1991-2000 Nissan Sentra?

    Yes. A1 CARDONE 66-6162 is listed for the front right side of the 1991-2000 Nissan Sentra. For another model, open the "Vehicles it fits" section to check your exact model and engine.

    How many splines does the A1 CARDONE CV drive axle have?

    The A1 CARDONE 66-6162 has a splined inboard joint and a splined outboard joint, each with 25 splines. Its steel shaft is 27 mm (1.063 in) in diameter.

    Does this A1 CARDONE CV axle include the ABS tone ring?

    Yes. A1 CARDONE 66-6162 includes a toothed ABS tone ring with 42 teeth.

    How can I tell a CV axle is wearing out?

    Common signs are loud clicking or snapping when you turn the wheel hard and accelerate, a thump with vibration under acceleration, or grease on the chassis from a torn boot. A shop can confirm the cause.

    Do A1 CARDONE axles need a new axle nut, or can I reuse the old one?

    Use the new nut: one is supplied with every unit, and a prevailing torque nut should never be reused. Tighten it with a torque wrench to the manufacturer's specification, never an impact wrench.

    Reviews

    No reviews yet — be the first to review this product.

    Write a Review