Rear Right Brake Caliper for 2006-2008 Dodge Ram 1500 & More - A1 CARDONE 18-B4894

$95.99
CARDONE Reman Disc Brake Caliper 18-B4894
CARDONE Reman Disc Brake Caliper 18-B4894

Vehicles this part fits
    Part number: 18-B4894
    UPC: 082617700085
    Weight: 18.60 LBS
    Item Package Quantity: 1
    $95.99
    Adding to cart… The item has been added

    Have questions?

    Ask an Expert
    CARDONE Reman Disc Brake Caliper P/N:18-B4894
    CARDONE Reman Disc Brake Caliper P/N:18-B4894
    $95.99
    $95.99

    A1 CARDONE 18-B4894 rear right brake caliper for the 2006-2008 Dodge Ram 1500 and other vehicles squeezes the brake pads against the rotor to slow the wheel. This remanufactured unloaded caliper comes with its mounting bracket.

    • Remanufactured with brand-new components, and every unit is 100% pressure-tested
    • Phenolic pistons resist cracking and pitting and handle great loads
    • Rubber seals replaced with new high temperature EPDM rubber
    • Special formulated rust inhibitor applied to the caliper
    • New bleeder screw for trouble-free bleeding and a positive seal

    Quick facts

    • Part: A1 CARDONE 18-B4894 brake caliper
    • Also called: disc brake caliper
    • Fits: 2006-2008 Dodge Ram 1500 and other vehicles
    • Position: Rear right
    • Material: Cast iron
    • Condition: Remanufactured

    A sticking disc brake caliper can show up as the vehicle pulling to one side, a brake that drags or fluid around the wheel. These signs alone do not prove the caliper is the problem; a restricted brake hose is another common cause.

    Fits

    The same rear right brake caliper also fits the 2003-2008 Dodge Ram 2500 and the 2003-2008 Dodge Ram 3500.

    Specifications

    Fit and size

    • Position: Rear right
    • Quantity per vehicle: 1 for this side
    • Piston quantity: 2
    • Piston diameter: 44.8564 mm (1.766 in)
    • Mounting hole diameter: 13.98989 mm (0.551 in)
    • Mounting hole thread size: M14 X 2.0
    • Inlet port size: 10.00366 mm (0.394 in), banjo fitting, thread M10x1.0
    • Bleeder thread size: M10x1.0

    Build and materials

    • Caliper type: Floating
    • Caliper casting material: Cast iron
    • Piston material: Phenolic
    • Finish: Oil emulsion, with rust-resistant coating
    • Condition: Remanufactured
    • Country of origin: Mexico

    In the box

    One rear right caliper with its bracket, hardware kit and instruction sheet. This listing holds one caliper and the rear right takes one; the rear left is a separate part ordered separately, and the two sides are normally replaced together. Brake pads and mounting bolts are not included, so plan on new bolts.

    Installation notes

    • New hardware and an instruction sheet come with the caliper.
    • A plastic cap plug protects every brake port thread.
    • Silicone grease is used on floating caliper mounting pins.
    • Use the brake fluid the vehicle maker specifies, from a new sealed container; the type is stamped on the master cylinder reservoir lid.

    Interchange: 5104758AA

    This part cross-references / interchanges with the following part numbers:

    5104758AA

    Frequently Asked Questions

    Is this caliper right for the 2006-2008 Dodge Ram 1500?

    Yes. The A1 CARDONE 18-B4894 is a rear right floating caliper listed for the 2006-2008 Dodge Ram 1500, and the bracket is included.

    Can I use this as a Ram 2500 brake caliper on a 2003-2008 Dodge Ram 2500?

    Yes. This rear right caliper fits the 2003-2008 Dodge Ram 2500. The rear left side is a separate part.

    What are the pistons made of on this A1 CARDONE brake caliper?

    The pistons are phenolic and the caliper body is cast iron. The caliper has two pistons, each 44.8564 mm (1.766 in) in diameter.

    Does the 18-B4894 caliper come with a bracket and hardware?

    Yes. A1 CARDONE 18-B4894 includes the caliper, bracket, hardware kit and instruction sheet. Brake pads and mounting bolts are not included.

    What grease goes on the mounting pins of this floating caliper?

    Silicone grease is used on floating caliper mounting pins. Use the brake fluid the vehicle maker specifies, from a new sealed container; the type is stamped on the master cylinder reservoir lid.

    Reviews

    No reviews yet — be the first to review this product.

    Write a Review

    Related Products

    !