A1 CARDONE 19-1910 front right brake caliper for the 1999-2005 Suzuki Grand Vitara and other vehicles clamps the brake pads against the rotor to slow the wheel. It is a remanufactured, unloaded floating caliper with a single piston.
- Rebuilt with brand-new components and a new hardware kit, then 100% pressure-tested
- Steel piston that resists cracking and pitting and handles heavy loads
- Rubber seals replaced with new high-temperature EPDM rubber
- Caliper treated with a specially formulated rust inhibitor
- New bleeder screw for trouble-free bleeding and a positive seal
Quick facts
- Part: A1 CARDONE 19-1910 brake caliper
- Also called: disc brake caliper
- Fits: 1999-2005 Suzuki Grand Vitara and other vehicles
- Position: Front right
- Material: Cast iron (caliper casting); steel (piston)
- Condition: Remanufactured
A sticking or leaking caliper can show up as the car pulling to one side under braking, uneven pad wear or fluid around the wheel. During a brake service, look at the slide pins for binding and at the brake hose for collapse before blaming the caliper, since either one can give a similar pull.
Fits
It fits the 1999-2005 Suzuki Grand Vitara, the 2002-2004 Suzuki XL-7 and the 1996-1998 Suzuki Sidekick, with one caliper per vehicle at this position. This listing is one caliper for the front right; the front left caliper on the same axle is a separate part and is normally replaced at the same time.
Specifications
Fit and size
- Position: Front right
- Quantity per vehicle: 1
- Piston quantity: 1
- Piston diameter: 2.249 in (57.1246 mm)
- Inlet fitting: Banjo, thread M10x1.0
- Inlet port size: 0.394 in (10.00366 mm)
- Mounting hole diameter: 0.424 in (10.76536 mm)
- Bleeder thread size: M8x1.0
Build and materials
- Caliper type: Floating, unloaded
- Casting material: Cast iron
- Piston material: Steel
- Finish: Oil emulsion, with rust-resistant coating
- Casting number: 17X
- Condition: Remanufactured
- Country of origin: Mexico
In the box
One caliper, an instruction sheet and a hardware kit with abutment clips, a bleeder screw and dust boots. Brake pads, the mounting bracket, mounting bolts, an anti-rattle spring and a bleeder screw cap are not included. The old mounting bolts may not be reusable, so plan on new bolts.
Installation notes
- An instruction sheet comes with the caliper.
- A plastic cap plug covers each brake port thread.
Interchange: 5510165D10 · 5510165D10999 · 5510165D20999 · 5510165D21999 · 5510177E00
This part cross-references / interchanges with the following part numbers:
Frequently Asked Questions
Is this the front right brake caliper for the 1996-1998 Suzuki Sidekick?
Yes. A1 CARDONE 19-1910 is a front right caliper that fits the 1996-1998 Suzuki Sidekick, one per vehicle at that position. The front left is a separate part.
Does this disc brake caliper come with brake pads or a mounting bracket?
No. This unloaded caliper comes with an instruction sheet and a hardware kit, but no pads, mounting bracket, mounting bolt or anti-rattle spring.
Is this A1 CARDONE brake caliper pressure-tested?
Yes. Every A1 CARDONE 19-1910 remanufactured caliper is 100% pressure-tested, and its rubber seals are replaced with new high-temperature EPDM rubber.
What is the piston made of on this A1 CARDONE caliper?
The piston is steel and measures 2.249 in (57.1246 mm) across. Swapping to a phenolic piston caliper is not recommended; follow the piston type the vehicle maker specified.
Which grease is used on the mounting pins of this floating brake caliper?
A silicone grease is used on floating caliper mounting pins. For brake fluid, use the type the vehicle maker recommends, which is stamped on the master cylinder reservoir lid.
Reviews
No reviews yet — be the first to review this product.
Write a ReviewWrite a Review