A1 CARDONE 19-B2711 front right brake caliper for the 2001-2006 Hyundai Santa Fe and other vehicles squeezes the pads against the rotor to slow the wheel. This remanufactured A1 CARDONE caliper is a floating design with two pistons, and it comes with its bracket and hardware.
- Every unit is 100% pressure-tested
- Two steel pistons that resist cracking and pitting and handle great loads
- Rubber seals replaced with new high-temperature EPDM rubber
- Specially formulated rust inhibitor treatment on the caliper
- New bleeder screws for trouble-free bleeding and a positive seal
- A plastic cap plug protects every brake port thread
Quick facts
- Part: A1 CARDONE 19-B2711 brake caliper
- Also called: disc brake caliper
- Fits: 2001-2006 Hyundai Santa Fe and other vehicles
- Position: Front right
- Material: Cast iron caliper casting; steel pistons
- Condition: Remanufactured
A disc brake caliper that sticks or leaks can show up as pulling to one side under braking, uneven pad wear or a fluid leak. Before you replace it, rule out binding slide pins, a collapsed brake hose and worn steering or suspension parts, because a pull has other sources too. Swap the front calipers as a pair; this listing is one front right caliper, and the front left is a separate part. One goes on each side of the front axle.
Fits
This front right caliper is a direct-fit replacement for the 2001-2006 Hyundai Santa Fe, the 2002-2003 Hyundai XG350 and the 2001 Hyundai XG300.
Specifications
Fit and size
- Position: Front right
- Quantity per application: 1
- Piston quantity: 2
- Piston diameter: 42.8244 mm (1.686 in)
- Mounting hole diameter: 11.98408 mm (0.472 in)
- Mounting hole thread: M12x1.25
- Inlet port size: 10.00366 mm (0.394 in), banjo fitting, M10x1.0 thread
- Bleeder thread size: M10x1.0
Build and materials
- Caliper type: Floating
- Condition: Remanufactured
- Caliper casting material: Cast iron
- Piston material: Steel
- Finish: Oil emulsion, with a rust-resistant coating
- Casting numbers: BC140044, BC412035
- Country of origin: Mexico
In the box
One caliper with its bracket, a hardware kit and an instruction sheet. Brake pads and mounting bolts are not included, so plan on new mounting bolts.
Installation notes
- The instruction sheet in the box covers the steps.
- Silicone grease is used on floating caliper mounting pins.
- Use the brake fluid the vehicle's maker calls for; the type is stamped on the master cylinder reservoir lid.
Interchange: 5819039A00
Frequently Asked Questions
Is this a brake caliper replacement for the 2001-2006 Hyundai Santa Fe?
Yes. A1 CARDONE 19-B2711 fits the front right of the 2001-2006 Hyundai Santa Fe. The front left side is a separate part.
Which side is this 2001-2006 Santa Fe brake caliper for?
A1 CARDONE 19-B2711 is for the front right. The front left takes its own caliper, which is ordered separately.
Does the 19-B2711 caliper come with its bracket and hardware?
Yes. A1 CARDONE 19-B2711 comes with its bracket, a hardware kit and an instruction sheet. Brake pads and mounting bolts are not included.
Is the piston in this A1 CARDONE brake caliper steel?
Yes. This caliper has two steel pistons, each 42.8244 mm (1.686 in) across. Swapping between steel and phenolic piston calipers is not recommended; follow the vehicle maker's specification.
What grease do floating caliper mounting pins take?
Silicone grease is used on floating caliper mounting pins. This caliper is a floating type, and its hardware kit includes new mounting pins where applicable.
