A1 CARDONE 19-B2881 front right brake caliper for the 2003-2007 Nissan Murano clamps the brake pads against the rotor to slow the wheel. This remanufactured A1 CARDONE caliper is a floating, single-piston unit sold unloaded, with its bracket.
- Brand-new components, and every unit is 100% pressure-tested
- Steel piston that resists cracking and pitting and handles heavy loads
- New high-temperature EPDM rubber seals replace the old ones
- Treated with a rust inhibitor to resist corrosion
- New bleeder screw for trouble-free bleeding and a positive seal
Quick facts
- Part: A1 CARDONE 19-B2881 brake caliper
- Also called: disc brake caliper
- Fits: 2003-2007 Nissan Murano and 2009-2011 Nissan Murano
- Position: Front right
- Material: Cast iron
- Condition: Remanufactured
A sticking or leaking disc brake caliper can show up as pulling to one side under braking or fluid around the caliper. Binding slide pins, a collapsed brake hose or worn pads can be behind those signs too, so find the cause before buying. Calipers on both sides of the front axle are normally replaced together; this listing is one, for the front right, and the left side is ordered separately.
Fits
This front right caliper fits the 2003-2007 Nissan Murano and the 2009-2011 Nissan Murano.
Specifications
Fit and size
- Position: Front right
- Pistons: 1
- Piston diameter: 63.5 mm (2.5 in)
- Inlet fitting: banjo, M10x1.0 thread
- Inlet port size: 10.00366 mm (0.394 in)
- Bleeder thread size: M10x1.0
- Mounting hole thread size: M14 X 1.5
- Mounting hole diameter: 13.98989 mm (0.551 in)
Build and materials
- Type: floating, unloaded
- Condition: Remanufactured
- Caliper casting material: cast iron
- Piston material: steel
- Finish: oil emulsion, with a rust-resistant coating
- Country of origin: Mexico
In the box
One caliper with its bracket, a hardware kit and an instruction sheet. Brake pads, the pad wear sensor and mounting bolts are not included, so plan on new mounting bolts.
Installation notes
- The instruction sheet in the box gives the steps.
- A plastic cap plug protects each brake port thread.
- Silicone grease goes on the mounting pins of a floating caliper.
Interchange: 410011AA0A · 41001CA000 · 41001CA005
This part cross-references / interchanges with the following part numbers:
410011AA0A, 41001CA000, 41001CA005
Frequently Asked Questions
Does this Nissan Murano caliper cover the 2009-2011 years as well as 2003-2007?
Yes. A1 CARDONE 19-B2881 fits the 2003-2007 Nissan Murano and the 2009-2011 Nissan Murano, on the front right side.
Does this A1 CARDONE brake caliper come with the bracket and hardware?
Yes. A1 CARDONE 19-B2881 includes the bracket, a hardware kit and an instruction sheet. Brake pads and mounting bolts are not included.
What piston size and material does this floating caliper have?
This front right caliper has one steel piston, 63.5 mm (2.5 in) in diameter, in a cast iron body.
What grease and brake fluid go with a floating caliper like this?
A silicone grease is used on floating caliper mounting pins. For fluid, use what the vehicle maker recommends; the type is stamped on the master cylinder reservoir lid.
Does the 41001CA000 number cross to this front right caliper?
Yes. A1 CARDONE 19-B2881 replaces 41001CA000, and the same listing also covers 410011AA0A and 41001CA005.
