A1 CARDONE 19-B3965 rear right brake caliper for the 2005 Hyundai Elantra clamps the brake pads against the rotor to slow the wheel. This remanufactured, unloaded caliper (also called a disc brake caliper) comes with its bracket but without pads.
- Remanufactured with brand-new components and 100% pressure-tested
- Steel piston that resists cracking and pitting and handles great loads
- Rubber seals replaced with new high temperature EPDM rubber
- Treated with a special formulated rust inhibitor
- New bleeder screw for trouble-free bleeding and a positive seal
Quick facts
- Part: A1 CARDONE 19-B3965 brake caliper
- Also called: disc brake caliper
- Fits: 2005 Hyundai Elantra
- Position: Rear right
- Material: Cast iron
- Condition: Remanufactured
A failing caliper can show as pulling to one side when braking, brake fluid around the wheel or uneven pad wear. Before you replace it, rule out sticking slide pins, a collapsed brake hose and worn steering or suspension parts, which can also cause pulling. Both rear calipers are normally replaced together; this listing is one.
Fits
This is a direct-fit brake caliper replacement for the 2005 Hyundai Elantra, which takes one caliper on the rear right; the rear left is ordered separately.
Specifications
Fit and size
- Position: rear right
- Quantity per application: 1
- Piston diameter: 33.909 mm (1.335 in)
- Mounting hole diameter: 10.00366 mm (0.394 in), thread M10x1.25
- Inlet port: 10.00366 mm (0.394 in), M10x1.0 inverted flare
- Bleeder thread size: M10x1.0
Build and materials
- Caliper type: floating, 1 piston
- Casting material: cast iron
- Piston material: steel
- Finish: oil emulsion, with rust-resistant coating
- Casting number: BC140018
- Condition: remanufactured
- Country of origin: Mexico
In the box
One caliper, mounting bracket, hardware kit and instruction sheet. Abutment clips, an anti-rattle spring, a bleeder screw and dust boots are also included. Brake pads, a pad wear sensor, a bleeder screw cap and a mounting bolt are not included, so plan on new mounting bolts.
Installation notes
- No programming is required.
- A plastic cap plug protects each brake port thread until installation.
- Silicone grease goes on floating caliper mounting pins.
- The instruction sheet in the box covers the steps.
Interchange: 583112DA10
Frequently Asked Questions
Will this A1 CARDONE brake caliper fit a 2005 Hyundai Elantra?
Yes. A1 CARDONE 19-B3965 is the rear right caliper for the 2005 Hyundai Elantra. The rear left side is a different part.
Does the A1 CARDONE caliper come with a mounting bracket?
Yes. A1 CARDONE 19-B3965 includes the bracket, abutment clips, an anti-rattle spring, a bleeder screw and dust boots. Brake pads and a mounting bolt are not included.
What piston size and bleeder thread does this rear right caliper have?
The single steel piston is 33.909 mm (1.335 in) in diameter, and the bleeder screw thread is M10x1.0. The inlet port is M10x1.0 with an inverted flare fitting.
How can I spot a leaking or sticking rear caliper?
During a brake service, look for wet brake fluid at the caliper, torn dust boots or one pad worn far more than the other. Pulling to one side when braking can also be a sign.
What grease goes on the mounting pins of this floating caliper?
A silicone grease is used on floating caliper mounting pins, and this rear caliper is a floating type. No programming is required, and an instruction sheet comes in the box.
