Delphi HP10185 fuel pump and sender assembly for the 1987-1989 Ford Bronco 6-cylinder 4.9L or V8 5.0L and the 1988-1989 Bronco V8 5.8L moves fuel from the tank to the engine. As a Delphi fuel pump assembly, it also carries the float arm and the metal fuel tubes on one hanger.
- Validated and tested pump assembly
- Delphi pump designed to operate under extreme temperatures with quick engine starts
- Metal tubes routed so they do not touch the tank at any point, which removes noise and vibration in operation
- Empty float height and float retention set for correct gas gauge readings
- Lower amperage draw puts less load on the vehicle's electrical system
Quick facts
- Part: Delphi HP10185 fuel pump and sender assembly
- Fits: the 1987-1989 Ford Bronco 6-cylinder 4.9L or V8 5.0L and the 1988-1989 Bronco V8 5.8L
- Condition: New
Long cranking, stalling or a fuel gauge that reads wrong can mean the pump or sender is wearing out. Before you replace this assembly, rule out a blown fuse, a failed relay, damaged wiring and a dirty fuel tank; a shop can test fuel pressure.
Fits
It fits the 1987-1989 Ford Bronco 6-cylinder 4.9L or V8 5.0L and the 1988-1989 Bronco V8 5.8L, and a Bronco takes just one. The pump is built to Delphi's OE standards, and the float matches OE specifications.
Specifications
- Quantity per vehicle: 1
- Type: fuel pump hanger assembly with float arm
- Condition: New
In the box
One fuel pump and sender assembly with float arm, two seals, two retainer clips and one instruction sheet.
Installation notes
- Check and clean the fuel tank before installing the new assembly.
- An instruction sheet comes with the part.
Interchange: 951-3000 · E8TZ 9H307-G · E8TZ 9H307-GA · PFS-23
4011031 · 4017223 · E2141S · E2484 · EHP10185 · 67069 · 69100 · 69111 · P74096 · P74523S · RE0096S · D0043H · A43008 · E16045 · FG174A · SP1152 · SP1165 · SP2012H · USEP2141S
This part cross-references / interchanges with the following part numbers:
4011031, 4017223, E2141S, E2484, EHP10185, 67069, 69100, 69111, P74096, P74523S, 951-3000, RE0096S, E8TZ 9H307-G, E8TZ 9H307-GA, PFS-23, D0043H, A43008, E16045, FG174A, SP1152, SP1165, SP2012H, USEP2141S
Frequently Asked Questions
Is this the 1989 Ford Bronco fuel pump for the 6-cylinder 4.9L, V8 5.0L and V8 5.8L?
Yes. Delphi HP10185 fits the 1987-1989 Ford Bronco 6-cylinder 4.9L or V8 5.0L and the 1988-1989 Bronco V8 5.8L, so a 1989 Bronco is covered with any of those engines.
What comes with the Delphi fuel pump and sender assembly?
Delphi HP10185 comes with the float arm, two seals, two retainer clips and an instruction sheet.
Does the float on this hanger match the original for gas gauge readings?
Yes. Empty float height and float retention match OE specifications, which supports a correct gas gauge reading.
Do the fuel tubes on Delphi HP10185 touch the tank?
No. The metal tubes are routed so they do not contact the tank at any point, which removes noise and vibration during operation.
Should the fuel tank be cleaned when installing this hanger assembly?
Yes. Check and clean the fuel tank before installing the assembly; the instruction sheet packed with the part covers the installation.
