Delphi Suspension Control Arm and Ball Joint Assembly P/N:TC2337
$185.99
(You save)
Replace a worn front left upper arm with the Delphi control arm and ball joint assembly TC2337. It fits many vehicles, among them the 2007-2011 Mercedes-Benz CL550, 2007-2011 Mercedes-Benz CL600 and 2008-2011 Mercedes-Benz CL63 AMG; see the Buyer's Guide tab for the full list and engine details. This front left upper unit locates the wheel and lets the integrated ball joint pivot through steering and suspension travel, and it installs as a direct-fit replacement for the listed Mercedes-Benz applications. Popping, clunking on bumps, uneven tire wear, or loose steering can be signs the original arm or ball joint may need replacing — if a failed arm or joint is the cause, this assembly replaces it.
Built to OE performance: Delphi applies its OE steering expertise to the aftermarket, testing below -40°C, above 120°C, and through 720 hours of salt spray, with dimensional and material analysis for OE-to-aftermarket compatibility.
100% inspected: Every arm gets crack detection and ultrasonic flaw detection so materials match OE specifications.
Micron-tolerance ball stud: The ball stud is machined to micron tolerances for durability and smooth joint operation.
Robot-welded, corrosion-protected: Robot welding delivers consistent quality, and anti-corrosion protection is applied to each part for corrosion prevention and enhanced appearance.
It's a control arm with an integrated ball joint for the front left upper position. It locates the wheel and lets the ball joint pivot through steering and suspension travel.
Which vehicles does this control arm fit?
It fits many vehicles, among them the 2007-2011 Mercedes-Benz CL550, 2007-2011 Mercedes-Benz CL600 and 2008-2011 Mercedes-Benz CL63 AMG. See the Buyer's Guide tab for the full list.
What testing is this control arm put through?
Delphi applies its OE steering expertise to the aftermarket, with testing below -40°C, above 120°C, 720 hours of salt spray, and 100% crack and ultrasonic flaw detection.
What are signs this control arm or ball joint may need replacing?
Clunking or popping over bumps, uneven tire wear, and loose or wandering steering can indicate a worn arm or joint. Diagnose the cause before replacing, as other parts can produce similar symptoms.
Does this assembly include the ball joint?
Yes. The ball joint is integrated into the assembly, with a ball stud machined to micron tolerances for durability and smooth joint operation.
Write a Review
Delphi
Delphi Suspension Control Arm and Ball Joint Assembly P/N:TC2337
Replace a worn suspension link with the Delphi control arm you can trust — the Delphi Suspension Control Arm and Ball Joint Assembly TC6332. This front left lower control arm drops in as a direct-fit...
Help keep your BMW's front-left wheel located and its steering connected with the Delphi control arm and ball joint assembly, MPN TC804 — a direct-fit replacement for the listed BMW models. It fits...
Fit a genuine Delphi control arm and help restore steady, controlled handling on your 2008-2013 Subaru Impreza with the Delphi Suspension Control Arm and Ball Joint Assembly TC7623. This is the front...
Help keep handling tight and controlled with the Delphi control arm and ball joint assembly (TC7298) — a Delphi control arm engineered as a direct-fit replacement for the rear upper rearward position...
Help keep the wheel located with the Delphi control arm and ball joint assembly (TC7873), engineered as a direct-fit replacement for the FRONT LEFT UPPER position. It bolts in on the 2014 Chevrolet...
WARNING:
These products can expose you to chemicals including lead and phthalates, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
