Front Right Lower Control Arm Bushing for 2003-2011 Ford Crown Victoria - Delphi TD4232W

$60.99
WARNING:California Proposition 65▾
Sold out
Delphi Suspension Control Arm Bushing TD4232W
Delphi Suspension Control Arm Bushing TD4232W - view 2
Delphi Suspension Control Arm Bushing TD4232W - view 3
Delphi Suspension Control Arm Bushing TD4232W - view 4
Delphi Suspension Control Arm Bushing TD4232W - view 5
Delphi Suspension Control Arm Bushing TD4232W - view 6
Delphi Suspension Control Arm Bushing TD4232W
Delphi Suspension Control Arm Bushing TD4232W - view 2
Delphi Suspension Control Arm Bushing TD4232W - view 3
Delphi Suspension Control Arm Bushing TD4232W - view 4
Delphi Suspension Control Arm Bushing TD4232W - view 5
Delphi Suspension Control Arm Bushing TD4232W - view 6

Vehicles this part fits
    Part number: TD4232W
    UPC: 689604322604
    Condition: New
    Weight: 6.05 LBS
    Item Package Quantity: 1
    $60.99

    Out of stock

    Have questions?

    Ask an Expert
    Delphi Suspension Control Arm Bushing P/N:TD4232W
    Delphi Suspension Control Arm Bushing P/N:TD4232W
    $60.99
    $60.99

    Help keep handling quiet and controlled with the Delphi Suspension Control Arm Bushing (P/N: TD4232W), a direct-fit replacement for 2003-2011 Ford Crown Victoria control arm bushings (see the "Vehicles it fits" section for engine-level fitment). This bushing serves the front right lower rearward position, cushioning the control arm where it mounts to the chassis so the suspension stays located while road vibration and noise are dampened.

    Delphi builds this from its OE safety technology used on millions of vehicles worldwide, backed by extensive dimensional and material analysis for close OE-to-aftermarket compatibility.

    • Designed to OE standards: a control arm bushing made to Delphi's OE standards.
    • Tested to the extreme: validated below -40°C and above 120°C and through 720 hours of salt-spray exposure.
    • Built for consistent life: manufactured to reduce noise and vibration.
    • Complete job: Delphi includes the necessary accessories for the installation.

    If worn, cracked, or separated bushings are the cause of clunking on acceleration or a vague, noisy ride, replacing them helps restore proper location of the control arm.

    Interchange: 523-670 · 4W7Z 5A486-AB
    523670 · 4W7Z5A486AB · K80836 · JBU1381

    Product information is for general reference and may contain errors. See our Disclaimer.

    This part cross-references / interchanges with the following part numbers:

    523-670, 4W7Z 5A486-AB, K80836, JBU1381

    Frequently Asked Questions

    What is a suspension control arm bushing?

    It is the cushion that mounts the control arm to the chassis, locating the arm through suspension travel while dampening road noise and vibration transmitted into the body.

    Does this Delphi TD4232W fit my 2003-2011 Ford Crown Victoria?

    It is a direct-fit replacement for the 2003-2011 Ford Crown Victoria. Check the "Vehicles it fits" section to confirm engine-level fitment for your vehicle.

    What position does this bushing serve?

    This bushing is cataloged for the front right lower rearward position on the listed applications.

    What are the signs this bushing may need replacing?

    Clunking on acceleration or deceleration, a vague or noisy ride, and a cracked or separated bushing can indicate wear. Diagnose the cause before replacing.

    Are installation accessories included?

    Delphi states it includes the necessary accessories for a complete job. Consult the vehicle service information for correct fasteners and torque, and whether any may be reused.

    Reviews

    No reviews yet — be the first to review this product.

    Write a Review

    Related Products

    !