Delphi Suspension Control Arm Bushing TD4275W
Delphi Suspension Control Arm Bushing TD4275W - view 2
Delphi Suspension Control Arm Bushing TD4275W - view 3
Delphi Suspension Control Arm Bushing TD4275W - view 4
Delphi Suspension Control Arm Bushing TD4275W - view 5
Delphi Suspension Control Arm Bushing TD4275W
Delphi Suspension Control Arm Bushing TD4275W - view 2
Delphi Suspension Control Arm Bushing TD4275W - view 3
Delphi Suspension Control Arm Bushing TD4275W - view 4
Delphi Suspension Control Arm Bushing TD4275W - view 5

Rear Upper Control Arm Bushing for 2005-2010 Jeep Grand Cherokee & More - Delphi TD4275W

Be the first to review this product
$25.99
WARNING:California Proposition 65▾
MPN: TD4275W
UPC: 689604335772
Item Package Quantity: 1
Adding to cart… The item has been added

Have questions?

Ask an Expert
Delphi Suspension Control Arm Bushing P/N:TD4275W
Delphi Suspension Control Arm Bushing P/N:TD4275W
$25.99

Help cushion the control arm and isolate road vibration with the Delphi Suspension Control Arm Bushing (TD4275W), a direct-fit replacement for the listed applications. It fits many vehicles, among them the 2005-2010 Jeep Grand Cherokee, 2008-2010 Jeep Liberty and 2007-2010 Dodge Nitro; see the Buyer's Guide tab for the full list. This suspension control arm bushing seats at the rear upper control-arm-to-frame position, cushioning the joint so the arm locates properly while road vibration is isolated from the chassis.

  • Tested to OE performance: Delphi applies its OE expertise to the aftermarket, running parts below -40°C, above 120°C and through 720 hours of salt spray, backed by extensive dimensional and material analysis for OE-to-aftermarket compatibility.
  • Designed to OE standards: engineered to Delphi's OE bushing standards.
  • Built to reduce noise and vibration: manufactured to reduce noise and vibration and for consistent service life.
  • Ready to install: includes the necessary accessories for a complete job.

Worn suspension bushings can show up as clunking or knocking over bumps, vibration through the body, uneven tire wear, and loose or wandering handling; if a failed rear upper bushing is the cause, this Delphi part replaces it. Diagnose the cause before replacing, and inspect both sides so worn parts are addressed together.

Interchange: 52089 629AB
52089629AB · 52089635AA · K200179 · RK641865 · MS25432 · JBU1804

This part cross-references / interchanges with the following part numbers:

52089 629AB, 52089635AA, K200179, RK641865, MS25432, JBU1804

Frequently Asked Questions

What does this control arm bushing do?

It cushions the rear upper control-arm-to-frame joint, locating the control arm while isolating road vibration and noise from the chassis.

Are these the right Jeep Grand Cherokee control arm bushings for a 2005-2010 model?

Yes — TD4275W is a direct-fit replacement for the 2005-2010 Jeep Grand Cherokee, and it also fits the 2008-2010 Jeep Liberty and 2007-2010 Dodge Nitro. See the Buyer's Guide tab for more.

What are the signs this bushing may need replacing?

Clunking or knocking over bumps, vibration through the body, uneven tire wear, and loose or wandering handling can point to worn bushings; diagnose the cause before replacing.

Where is this bushing located?

It fits the rear upper control-arm-to-frame position on the listed applications.

Does it come with what I need to install it?

Delphi includes the necessary accessories for a complete job. Consult the vehicle service information for the correct torque and installation procedure.

Related Products

!