Delphi Suspension Stabilizer Bar Link Kit P/N:TC7836
$31.99
(You save)
Quiet the front-end clunks and keep your stabilizer bar tied firmly to the suspension with the Delphi Sway Bar Link Kit (TC7836). It drops in as a direct-fit front replacement for the 2005-2006 and 2008-2011 Mazda Tribute, 2006-2011 Mitsubishi Eclipse, 2004-2008 and 2010-2011 Mitsubishi Endeavor, and 2004-2011 Mitsubishi Galant — see the Buyer's Guide tab for engine-level fitment.
Delphi builds its aftermarket steering and suspension parts on the same OE expertise fitted to millions of vehicles worldwide, with extensive dimensional and material analysis for close OE-to-aftermarket compatibility:
Tested to the extreme: withstands temperatures below -40°C and above 120°C and endures 720 hours of salt spray.
Fatigue tested to guard against premature failure.
Machined to micron tolerances for durability and smooth joint operation.
Anti-corrosion protection applied to each part for corrosion prevention and enhanced appearance.
This front sway bar link kit connects the stabilizer (sway) bar to the suspension so the bar can resist body roll through turns. If worn links are the cause of clunking or rattling over bumps and looser handling in corners, this kit replaces them.
It's a front-position direct fit for the 2005-2006 and 2008-2011 Mazda Tribute, 2006-2011 Mitsubishi Eclipse, 2004-2008 and 2010-2011 Mitsubishi Endeavor, and 2004-2011 Mitsubishi Galant. See the Buyer's Guide tab for engine-level detail.
What does a stabilizer bar link kit do?
The link connects the stabilizer (sway) bar to the suspension, allowing the bar to resist body roll and keep the vehicle flatter through turns.
What are the signs my sway bar links may need replacing?
Common signs include clunking or rattling noises over bumps, knocking when cornering, and looser, less-controlled handling. Have the cause diagnosed, since other suspension parts can produce similar symptoms.
Is this part corrosion protected?
Yes. Delphi applies anti-corrosion protection to each part for corrosion prevention and enhanced appearance, and the design is tested through 720 hours of salt spray.
How durable is the Delphi TC7836?
It is fatigue tested against failure, machined to micron tolerances for smooth joint operation, and validated across temperatures below -40°C and above 120°C for demanding conditions.
Write a Review
Delphi
Delphi Suspension Stabilizer Bar Link Kit P/N:TC7836
Keep body lean in check and quiet the clunks with the Delphi Rear Suspension Stabilizer Bar Link Kit (TC2616) — a direct-fit replacement for the 2002-2007 Mitsubishi Lancer (see the Buyer's Guide tab...
Tighten up front-end response and quiet the clunks with the Delphi Suspension Stabilizer Bar Link Kit TC6165. These front sway bar links connect the stabilizer bar to the suspension, transferring...
Quiet the clunks and keep the rear stabilizer bar tied to the suspension with the Delphi Suspension Stabilizer Bar Link Kit TC6526. This rear-position stabilizer bar link kit drops in as a direct-fit...
Keep body roll in check and quiet the rattles with the Delphi Front Suspension Stabilizer Bar Link Kit TC6540. This front sway bar link connects the stabilizer bar to the suspension so the bar can...
Tie the front stabilizer bar to the suspension and help control body roll through every corner with the Delphi Suspension Stabilizer Bar Link Kit (TC2265). This front sway bar link kit is a...
WARNING:
These products can expose you to chemicals including lead and phthalates, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
