Dorman 521-892 front right lower control arm with ball joint for the 2010-2015 Chevrolet Cruze and other vehicles connects the wheel to the suspension. This Dorman suspension control arm and ball joint assembly brings the arm, ball joint and bushings together in one piece.
- Pinch-type ball joint stud with a 14 mm thread diameter
- Evaluation process aimed at a smooth ride, directional stability and predictable dynamics
- Pre-installed ball joint and bushings save time and labor
- Additional coatings resist rust and corrosion
- Aluminum control arm with rubber bushings
Quick facts
- Part: Dorman 521-892 control arm with ball joint
- Also called: control arm and ball joint assembly
- Fits: 2010-2015 Chevrolet Cruze and other vehicles
- Position: Front right lower
- Material: Aluminum
- Condition: New
A worn arm can show up as a clunk over bumps, uneven front tire wear or loose steering feel. Those signs alone do not prove this part is the problem, since a worn tie rod end can cause a similar clunk. Both front arms are normally replaced together, and this listing is one arm for the front right, so the front left is ordered separately. The 2010-2015 Chevrolet Cruze takes one at the front right.
Fits
Dorman made this OE Solutions control arm with ball joint as a direct replacement for the original equipment, and it fits the 2010-2015 Chevrolet Cruze, the 2012-2017 Buick Verano and the 2016 Chevrolet Cruze Limited. Cars not named here are covered in the "Vehicles it fits" section, so look yours up there.
Specifications
Fit and size
- Position: Front right lower
- Quantity per vehicle: 1
- Mounting hole diameter: 12.1 mm
- Mounting hole quantity: 1
- Ball joint thread diameter: 14 mm
- Control arm maximum width: 288.5 mm
- Control arm maximum length: 237 mm
Build and materials
- Control arm material: Aluminum
- Bushing material: Rubber
- Control arm type: Casting/Forged
- Ball joint stud type: Pinch
- Grade: Standard replacement
- Condition: New
- Country of origin: Thailand
In the box
One control arm with ball joint, with mounting hardware. A grease fitting is not included.
Installation notes
- The assembly arrives pre-greased.
Interchange: 810-521892B · 623.62003
TC2588 · CA12565 · 13272606 · 13334023 · 13463245 · RK621751 · GS501134 · CMS501134 · 2606753 · 5CB50325 · SK521892 · 1503040 · X07CJ1148 · JTC1476 · V400898
This part cross-references / interchanges with the following part numbers:
810-521892B, 623.62003, TC2588, CA12565, 13272606, 13334023, 13463245, RK621751, GS501134, CMS501134, 2606753, 5CB50325, SK521892, 1503040, X07CJ1148, JTC1476, V400898
Frequently Asked Questions
Is this Dorman suspension control arm right for the 2012-2017 Buick Verano?
Yes. Dorman 521-892 fits the 2012-2017 Buick Verano as the front right lower control arm with ball joint. The front left is a separate part.
Are the Dorman control arm bushings already installed?
Yes. The rubber bushings come pre-installed along with the ball joint, and mounting hardware is included in the box.
What is the Dorman control arm made of?
Dorman 521-892 has an aluminum control arm of casting/forged type, with rubber bushings. The ball joint has a 14 mm thread diameter.
How do I tell if the Dorman lower control arm on the front right is worn?
Clunks over bumps, uneven front tire wear and loose steering feel are the signs drivers notice. A shop can inspect the bushings and ball joint for wear.
Is there a grease fitting with Dorman 521-892?
No. A grease fitting is not included with Dorman 521-892, but the assembly arrives pre-greased.
