Heater Hose for 2006-2011 Chevrolet Impala & More - Gates 18786

$38.99

Vehicles this part fits

    Part number: 18786
    UPC: 072053179316
    Condition: New
    Weight: 0.65 LBS
    Item Package Quantity: 1
    $38.99
    Adding to cart… The item has been added

    Have questions?

    Gates HVAC Heater Hose P/N:18786
    Gates HVAC Heater Hose P/N:18786
    $38.99
    $38.99

    Gates 18786 heater hose for the 2006-2011 Chevrolet Impala V6 3.5L or 3.9L and other vehicles carries engine coolant to and from the heater. The Gates molded heater hose, also called an HVAC heater hose, is part of the engine's coolant circuit.

    • Gates Small I.D. Molded Coolant Hose, factory-molded for smaller, tighter engine compartments
    • Hose used for coolant, water and air applications, and also approved for marine applications
    • EPDM tube and cover with synthetic fiber knit reinforcement
    • Engineered to resist electrochemical degradation, the leading cause of hose failure
    • Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
    • Temperature range: -40 Deg. F to 275 Deg. F (-40 Deg. C to 135 Deg. C)

    Quick facts

    • Part: Gates 18786 heater hose
    • Also called: HVAC heater hose
    • Fits: 2006-2011 Chevrolet Impala V6 3.5L or 3.9L and other vehicles
    • Position: Heater to engine, heater to pipe-1, heater to pipe-2, heater inlet, pipe-4 to heater, tee to thermostat, tee-3 to thermostat
    • Material: EPDM
    • Condition: New

    Cracks, a soft or swollen feel, or coolant seepage at the ends, seen with the engine cool, can mean a heater hose is wearing out. A leaking heater core, a stuck thermostat or a weak water pump can be behind coolant loss or poor cabin heat too, so find the cause before buying a hose.

    Fits

    This molded EPDM heater hose fits the 2006-2011 Chevrolet Impala V6 3.5L or 3.9L, the 2006 Chevrolet Monte Carlo V6 3.9L and the 2006-2007 Monte Carlo V6 3.5L, and the 1997-2000 Mitsubishi Diamante V6 3.5L. Many other models and engines fit as well, so open the "Vehicles it fits" section and look up your exact model and engine.

    Specifications

    Fit and size

    • Position: Heater to engine, heater to pipe-1, heater to pipe-2, heater inlet, pipe-4 to heater, tee to thermostat, tee-3 to thermostat
    • Quantity per vehicle: 1
    • Centerline length: 450 mm (17.7 in)
    • Inside diameter, both ends: 16 mm (0.62 in)

    Build and materials

    • Construction: Molded
    • Material: EPDM
    • Reinforcement: Synthetic fiber knit
    • Condition: New
    • Country of origin: United States

    In the box

    One heater hose. This listing holds one hose, and each vehicle takes one.

    Installation notes

    • Gates recommends replacing hose clamps each time a new coolant hose is installed.
    • Do not use for fuel or oil transfer applications.

    Interchange: E8UZ 18472 A · F0UZ 18472 A
    16059M · D90898 · 14034308 · 15286611 · 15821186 · 15893669 · 63300 · 0K24D61212 · 0K24D61212A · AW342621 · 10786

    Product information is for general reference and may contain errors. See our Disclaimer.

    This part cross-references / interchanges with the following part numbers:

    16059M, 18786, D90898, E8UZ 18472 A, F0UZ 18472 A, 14034308, 15286611, 15821186, 15893669, 63300, 0K24D61212, 0K24D61212A, AW342621, 10786

    Frequently Asked Questions

    Is this Impala heater hose right for the 2006-2011 Chevrolet Impala V6 3.5L or 3.9L?

    Yes, Gates 18786 is listed for the 2006-2011 Chevrolet Impala with either the V6 3.5L or the V6 3.9L. For other models, open the "Vehicles it fits" section.

    What are the inside diameter and length of the Gates 18786 heater hose?

    Gates 18786 has a 16 mm (0.62 in) inside diameter at both ends and a centerline length of 450 mm (17.7 in).

    Is this Gates 1 heater hose a single hose or a set?

    It is a single molded hose. The listing holds one, and each vehicle takes one.

    What temperature range and SAE spec does this EPDM heater hose meet?

    It is rated for -40 Deg. F to 275 Deg. F (-40 Deg. C to 135 Deg. C) and meets SAE 20R3 Type EC Class D-1 and D-2 specifications.

    Should I replace the hose clamps when installing this heater hose?

    Yes, Gates recommends replacing hose clamps each time a new coolant hose is installed. Gates 18786 is not for fuel or oil transfer applications.

    Reviews

    No reviews yet — be the first to review this product.

    Write a Review