Standard Ignition VR-606 voltage regulator for the 1950-1951 Ford Country Sedan 6-cylinder 3.7L, the 1952-1953 Country Sedan 6-cylinder 3.5L, the 1954-1956 Country Sedan 6-cylinder 3.6L and other vehicles controls the voltage that the charging system sends to the battery. It is an electronic regulator in the starting and charging system.
- Quality control from the components through the finished regulator
- Electronic PC board encapsulated in epoxy to resist vibration and corrosion of electrical connections
- Circuit board manufactured by Standard Ignition for precise operation and reliability
- High grade materials and components for a longer service life
Quick facts
- Part: Standard Ignition VR-606 voltage regulator
- Fits: the 1950-1951 Ford Country Sedan 6-cylinder 3.7L, the 1952-1953 Country Sedan 6-cylinder 3.5L, the 1954-1956 Country Sedan 6-cylinder 3.6L and other vehicles
- Condition: New
A charging warning light, dim or flickering lights, or a battery that keeps running low can mean the regulator is failing. Before you replace it, rule out a weak battery, a loose or corroded wiring connection and the generator, since any of them can look the same at the dash.
Fits
The 1950-1951 Ford Country Sedan 6-cylinder 3.7L, the 1952-1953 Country Sedan 6-cylinder 3.5L and the 1954-1956 Country Sedan 6-cylinder 3.6L are all covered by this regulator, which also fits the 1950-1951 Ford Country Squire 6-cylinder 3.7L, the 1952-1953 Country Squire 6-cylinder 3.5L, the 1954-1956 Country Squire 6-cylinder 3.6L, the 1954 Mercury Custom V8 4.2L, the 1955 Custom V8 4.8L, the 1956 Custom V8 5.1L and many other Ford and Mercury models. A 1954-1956 Country Sedan 6-cylinder 3.6L takes one regulator. If your car is not named here, open the "Vehicles it fits" section to check your exact model and engine.
Specifications
Fit and size
- Quantity per vehicle: 1
- Voltage: 6 V
- Amperage rating: 50 A
- Mounting location: fender
- Connector: 1 flat, male
- Terminals: 3, screw and blade, male
Build and materials
- Construction: electronic PC board encapsulated in epoxy
- Condition: New
- Country of origin: United States
In the box
One voltage regulator with instructions. Mounting hardware and a mounting bracket are not included, so plan on new fasteners, since the old ones may not be reusable.
Interchange: R702 · IGNB10121 · VR403 · B3TZ10505A
Product information is for general reference and may contain errors. See our Disclaimer.
This part cross-references / interchanges with the following part numbers:
R702, IGNB10121, VR403, B3TZ10505A
Frequently Asked Questions
Does the Standard Ignition VR-606 fit a 1954-1956 Ford Country Sedan 6-cylinder 3.6L?
Yes. The Standard Ignition VR-606 voltage regulator fits the 1954-1956 Ford Country Sedan 6-cylinder 3.6L. For other models and engines, open the "Vehicles it fits" section.
Does the VR-606 voltage regulator come with mounting hardware?
No. The Standard Ignition VR-606 comes with instructions but without mounting hardware or a mounting bracket, so plan on new fasteners for the install.
Is this a 6-volt or 12-volt voltage regulator, and what are its terminals?
This voltage regulator is a 6-volt unit rated at 50 A. It has one flat male connector and three male terminals of the screw and blade type.
How do I check the connections on a voltage regulator before replacing it?
With the engine off, look at the three terminals and the wiring connections for corrosion, looseness or damage. A shop can test charging output with the engine running.
How is the VR-606 voltage regulator's circuit board protected from vibration?
The electronic PC board in this voltage regulator is encapsulated in epoxy, which is intended to resist failure from vibration and corrosion of electrical connections.
