Mevotech TTX Suspension Control Arm and Ball Joint Assembly P/N:CTXMS50152
$191.99
(You save)
Keep your front suspension tight and precisely located with the Mevotech TTX control arm and ball joint assembly, MPN CTXMS50152. This front left lower unit installs as a direct-fit replacement for the 2007-2016 Chevrolet Silverado 1500 and Tahoe, 2007-2014 Cadillac Escalade, GMC Yukon (2007-2014 and 2016), and many more GM full-size trucks and SUVs — see the Buyer's Guide tab for the full list. The arm locates the front wheel and its integrated ball joint provides the lower pivot point; if a worn arm or ball joint is behind clunking over bumps, loose steering, or uneven tire wear, this assembly replaces it.
Maximum toughness: patented sintered bearings for longer-lasting performance, built to meet or exceed OE specifications with cast steel construction.
Superior seal: Integri-Boot™ design built into the ball joint helps lock out moisture and contaminants.
Simple to service: a 180-degree SAE grease fitting is included, and the ball joint secures to the vehicle with a part-specific slotted castle nut and snap cotter pin.
Longer service life: Repel-TEK™ surface treatment helps prevent rust build-up, plus knurled rubber bushings that grip the sub-frame.
Upgraded rubber bushings, a larger-sphere ball stud, a thicker ball-joint flange, and pre-applied Nylok thread adhesive round out this Labor Saver™ design.
Frequently Asked Questions
What is the Mevotech TTX CTXMS50152 control arm and ball joint assembly?
It is a front left lower suspension control arm with an integrated ball joint. The arm locates the front wheel while the ball joint provides the lower steering pivot for the listed GM trucks and SUVs.
Does this fit my Tahoe?
It is listed for the 2007-2016 Chevrolet Tahoe as a front left lower unit. Confirm your year and model against the Buyer's Guide tab before ordering.
What are the signs this control arm or ball joint may need replacing?
Common signs include clunking over bumps, loose or wandering steering, and uneven front tire wear. Have the cause diagnosed, since these symptoms can come from other worn suspension parts.
Is any mounting hardware included?
Yes. It comes with a part-specific slotted castle nut, an easy snap cotter pin, and a 180-degree SAE grease fitting for servicing.
How is this Mevotech TTX assembly built for durability?
It uses cast steel construction to meet or exceed OE specifications, patented sintered bearings, an Integri-Boot™ ball joint seal, and Repel-TEK™ surface treatment to help prevent rust build-up.
Write a Review
MEVOTECH
Mevotech TTX Suspension Control Arm and Ball Joint Assembly P/N:CTXMS50152
Get a strong, easy-installing Mevotech TTX control arm back under your truck or SUV with the Mevotech TTX Suspension Control Arm and Ball Joint Assembly (CTXK80670), a front right upper unit...
Swap out a worn Ram 1500 lower control arm with the Mevotech TTX Suspension Control Arm and Ball Joint Assembly (CTXMS25149), a front left lower unit engineered for high-usage passenger trucks,...
Replace a worn front right lower control arm and ball joint in one bolt-in unit with the Mevotech TTX Suspension Control Arm and Ball Joint Assembly (CTXMS25150), a direct-fit Ram 1500 lower control...
Locate the front wheel and provide its lower pivot with the Mevotech TTX Suspension Control Arm and Ball Joint Assembly CTXK80397, a front right lower unit engineered for high-usage commercial and...
Upgrade your front suspension with the Mevotech TTX control arm and ball joint assembly (MPN CTXMS501240), a heavy-duty replacement for the front right lower position on the 2015-2022 Chevrolet...
WARNING:
These products can expose you to chemicals including lead and phthalates, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
