Delphi Suspension Stabilizer Bar Bushing Kit P/N:TD4185W
$11.99
(You save)
Quiet a clunking, rattling front sway bar and keep the stabilizer bar properly located to the frame with the Delphi Suspension Stabilizer Bar Bushing Kit (TD4185W). These front, frame-side stabilizer bar bushings insulate the bar where it mounts to the frame, and worn originals often show up as knocking or looseness over bumps and added body roll in turns. It installs as a direct-fit replacement for the 2005-2013 Chrysler 300, 2008-2013 Dodge Challenger, 2006-2013 Dodge Charger, and 2005-2008 Dodge Magnum — see the Buyer's Guide tab for engine-level details.
Designed to OE standards: Delphi backs it with extensive dimensional and material analysis for close compatibility between the OE and aftermarket part.
Built for consistent life: manufactured for consistent service and tested to the extreme — enduring below -40°C and over 120°C plus 720 hours of salt spray.
Noise reduction: manufactured to reduce noise at the stabilizer bar mounting points.
Smoother ride: designed to help restore the vehicle's smooth ride when worn bushings are the cause.
Backed by Delphi's OE safety technology fitted to millions of vehicles worldwide.
What is a stabilizer bar bushing kit and what does it do?
It's the set of bushings that cushion the front stabilizer (sway) bar where it mounts to the frame, locating the bar and helping control body roll while reducing noise at the mounting points.
Does the Delphi TD4185W kit fit my vehicle?
It's a direct-fit replacement for the 2005-2013 Chrysler 300, 2008-2013 Dodge Challenger, 2006-2013 Dodge Charger, and 2005-2008 Dodge Magnum. Check the Buyer's Guide tab for engine-level fitment.
What are signs my front sway bar bushings may need replacing?
Common signs include clunking or rattling from the front over bumps, a loose or knocking feel, and increased body roll in corners. Have the cause diagnosed, as other parts can produce similar symptoms.
Is this a front or rear kit?
This kit is for the front stabilizer bar, mounting the bar to the frame (front-to-frame position).
How is this Delphi kit tested for durability?
Delphi tests to the extreme for OE performance: the parts withstand temperatures below -40°C and over 120°C and are exposed to 720 hours of salt spray, with dimensional and material analysis for OE compatibility.
Write a Review
Delphi
Delphi Suspension Stabilizer Bar Bushing Kit P/N:TD4185W
Quiet a clunking rear sway bar and keep it located under hard cornering with the Delphi Suspension Stabilizer Bar Bushing Kit (P/N: TD4177W). This kit cushions the rear stabilizer bar where it mounts...
Keep the rear stabilizer bar located and quiet with the Delphi Suspension Stabilizer Bar Bushing Kit (TD5070W). These bushings secure the rear stabilizer bar to the frame, cushioning it against the...
Quiet a clunking, knocking rear sway bar and keep the stabilizer bar located properly with the Delphi Suspension Stabilizer Bar Bushing Kit (TD996W). This rear sway bar bushing kit cushions the bar...
Quiet a clunking, rattling front sway bar and help keep your Mercedes-Benz cornering flat with the Delphi Suspension Stabilizer Bar Bushing Kit TD5885W. This front-to-frame stabilizer bar bushing kit...
Quiet a clunking front sway bar and keep the stabilizer bar located where it belongs with the Delphi Suspension Stabilizer Bar Bushing Kit TD671W. These front stabilizer bar bushings cushion the bar...
WARNING:
These products can expose you to chemicals including lead and phthalates, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
