Delphi Suspension Stabilizer Bar Link Kit P/N:TC1359
$25.99
(You save)
Keep your Volvo's front stabilizer bar tied tightly to the suspension with the Delphi Suspension Stabilizer Bar Link Kit TC1359. This front sway bar link kit connects the front stabilizer bar to the suspension so the bar can resist body roll and help keep the car flat through turns. It installs as a direct-fit replacement for the 1990-1993 Volvo 240, 1979-1984 Volvo 242, 1979-1989 Volvo 244, 1979-1989 Volvo 245, 1979-1981 Volvo 262, 1979-1982 Volvo 264 and 1979-1981 Volvo 265.
Delphi applies its OE steering-and-suspension expertise to this aftermarket link, backing it with extensive dimensional and material analysis for close OE-to-aftermarket compatibility.
Extreme-condition tested: validated below -40°C and above 120°C and through 720 hours of salt-spray exposure.
Fatigue tested: Delphi sway bar links are fatigue tested to help avoid failure.
Ultrasonic molding: built with ultrasonic molding to help prevent future weld breakage.
Micron-tolerance machining: machined to micron tolerances for durable, smooth joint operation, with anti-corrosion protection applied to each part.
Worn links often announce themselves with clunking or rattling over bumps and looser handling; if a failed link is the cause, this kit replaces it.
It connects the front stabilizer (sway) bar to the suspension so the bar can resist body roll, helping keep the vehicle flatter and more stable through turns.
Which vehicles does the Delphi TC1359 fit?
It's a front-position link for the 1990-1993 Volvo 240, 1979-1984 Volvo 242, 1979-1989 Volvo 244 and 245, 1979-1981 Volvo 262, 1979-1982 Volvo 264 and 1979-1981 Volvo 265.
How is this Delphi link built for durability?
It's fatigue tested to help avoid failure, molded ultrasonically to help prevent weld breakage, machined to micron tolerances, and given anti-corrosion protection.
What conditions has it been tested against?
Delphi validates the part below -40°C and above 120°C and through 720 hours of salt-spray exposure for OE-level performance.
What are signs my sway bar link may need replacing?
Clunking or rattling over bumps and looser, less-controlled handling can indicate a worn link. Diagnose the cause first; if the link is at fault, this kit replaces it.
Write a Review
Delphi
Delphi Suspension Stabilizer Bar Link Kit P/N:TC1359
Keep body lean in check and quiet the clunks with the Delphi Rear Suspension Stabilizer Bar Link Kit (TC2616) — a direct-fit replacement for the 2002-2007 Mitsubishi Lancer (see the Buyer's Guide tab...
Tighten up front-end response and quiet the clunks with the Delphi Suspension Stabilizer Bar Link Kit TC6165. These front sway bar links connect the stabilizer bar to the suspension, transferring...
Quiet the clunks and keep the rear stabilizer bar tied to the suspension with the Delphi Suspension Stabilizer Bar Link Kit TC6526. This rear-position stabilizer bar link kit drops in as a direct-fit...
Keep body roll in check and quiet the rattles with the Delphi Front Suspension Stabilizer Bar Link Kit TC6540. This front sway bar link connects the stabilizer bar to the suspension so the bar can...
Tie the front stabilizer bar to the suspension and help control body roll through every corner with the Delphi Suspension Stabilizer Bar Link Kit (TC2265). This front sway bar link kit is a...
WARNING:
These products can expose you to chemicals including lead and phthalates, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
