A1 CARDONE 19-B1910 front right brake caliper for the 1999-2005 Suzuki Grand Vitara and other vehicles presses the brake pads against the rotor to slow the wheel. This remanufactured A1 CARDONE caliper is a floating design with one steel piston.
- 100% pressure-tested after remanufacturing
- Piston is resistant to cracking and pitting and handles great loads
- Rubber seals replaced with new high-temperature EPDM rubber
- Rust-inhibitor treatment with an oil emulsion finish
- New bleeder screw for a positive seal; plastic cap plugs cover the brake port threads
Quick facts
- Part: A1 CARDONE 19-B1910 brake caliper
- Also called: disc brake caliper
- Fits: 1999-2005 Suzuki Grand Vitara and other vehicles
- Position: Front right
- Material: Cast iron casting, steel piston
- Condition: Remanufactured
A failing caliper can show up as the vehicle pulling to one side under braking, brake fluid around the caliper or uneven pad wear. Before you replace it, rule out a collapsed brake hose, sticking slide pins or a worn pad on that side, since any of them can produce similar pulling.
Fits
It is a brake caliper for the 1999-2005 Suzuki Grand Vitara, the 2002-2004 Suzuki XL-7 and the 1996-1998 Suzuki Sidekick. This listing is one caliper for the front right; the front left is a separate part, and both sides are normally replaced together. The 1999-2005 Suzuki Grand Vitara takes one caliper at the front right.
Specifications
Fit and size
- Position: front right
- Quantity per application: 1
- Piston quantity: 1
- Piston diameter: 57.1246 mm (2.249 in)
- Mounting hole: 11.98408 mm (0.472 in) diameter, M12x1.25 thread
- Inlet port: 10.00366 mm (0.394 in), banjo fitting, M10x1.0 thread
- Bleeder thread size: M8x1.0
Build and materials
- Type: floating, unloaded, with bracket
- Condition: remanufactured
- Casting material: cast iron
- Piston material: steel
- Finish: oil emulsion, with a rust-resistant coating
- Country of origin: Mexico
In the box
One brake caliper with its bracket, a hardware kit and an instruction sheet. Brake pads and mounting bolts are not included, so plan on new mounting bolts rather than reusing the old ones.
Installation notes
- No programming is required.
- Use the brake fluid the vehicle maker recommends; the type is stamped on the master cylinder reservoir lid, and it should come from a sealed container.
- A silicone grease is used on floating caliper mounting pins.
Interchange: 5510165D10 · 5510165D20999 · 5510177E00
This part cross-references / interchanges with the following part numbers:
5510165D10, 5510165D20999, 5510177E00
Frequently Asked Questions
Is this A1 CARDONE brake caliper the right one for the front right of a 1999-2005 Suzuki Grand Vitara?
Yes. A1 CARDONE 19-B1910 is the front right caliper for the 1999-2005 Suzuki Grand Vitara, and the front left side takes a separate caliper.
Does this disc brake caliper come with its mounting bracket?
Yes. It comes with the bracket, a hardware kit and an instruction sheet. Brake pads and mounting bolts are not included.
What size is the piston on the A1 CARDONE 19-B1910?
The A1 CARDONE 19-B1910 has one steel piston, 57.1246 mm (2.249 in) in diameter, in a floating caliper with a cast iron casting.
What are signs a floating caliper may be wearing out?
Pulling to one side when braking, brake fluid around the caliper or uneven pad wear can mean a caliper is failing. A shop can test the brakes to confirm.
Does the 19-B1910 caliper need programming or a special brake fluid?
No programming is required for the A1 CARDONE 19-B1910. Use the brake fluid the vehicle maker recommends; the type is stamped on the master cylinder reservoir lid.
