Delphi HP10010 fuel pump hanger for the 1988-1989 Oldsmobile Cutlass Supreme V6 2.8L, the 1989-1991 Cutlass Supreme V6 3.1L, the 1990-1991 Cutlass Supreme 4-cylinder 2.3L, the 1991 Cutlass Supreme V6 3.4L and other vehicles supports the fuel pump and float arm inside the fuel tank. It is built to Delphi's OE standards.
- Designed for operation in extreme temperatures with quick engine starts
- Metal tubes routed so they do not contact the tank at any point, to avoid noise and vibration in operation
- Empty float height and float retention held to specification for a correct fuel gauge reading
- Validated and tested by Delphi
- Lower amperage draw puts less load on the vehicle's electrical system
Quick facts
- Part: Delphi HP10010 fuel pump hanger
- Also called: fuel pump hanger assembly
- Fits: the 1988-1989 Oldsmobile Cutlass Supreme V6 2.8L, the 1989-1991 Cutlass Supreme V6 3.1L, the 1990-1991 Cutlass Supreme 4-cylinder 2.3L, the 1991 Cutlass Supreme V6 3.4L and other vehicles
A fuel gauge that reads wrong, hard starting or stalling can point to the hanger. A clogged fuel filter, a failing relay or a blocked fuel line may be behind these symptoms too, so track down the cause before you buy a new hanger.
Fits
This hanger fits the 1988-1989 Pontiac Grand Prix V6 2.8L, the 1989-1991 Grand Prix V6 3.1L, the 1990-1991 Grand Prix 4-cylinder 2.3L, the 1991 Grand Prix V6 3.4L, the 1990 Chevrolet Lumina V6 3.1L, the 1990-1991 Lumina 4-cylinder 2.5L and the 1991 Lumina V6 3.4L, along with the Cutlass Supreme engines named above. If your car is not named here, open the "Vehicles it fits" section and look up your exact model and engine.
Specifications
- Quantity per vehicle: 1
- Float arm: included
- Tubes: metal
In the box
One fuel pump hanger with float arm, one seal, one lock ring, two O-rings and one instruction sheet. This listing holds one hanger, and each vehicle takes one.
Installation notes
- Check the fuel tank and clean it before the hanger goes in.
- The instruction sheet in the box covers the installation steps.
Interchange: 951-5003 · 692-015
25028349 · 25028350 · 4011033 · 4017118 · E3265 · CHP10010 · P74037 · P77380H · AFS0206P · RE0207P · 19111392 · SP09A1H
This part cross-references / interchanges with the following part numbers:
25028349, 25028350, 4011033, 4017118, E3265, CHP10010, P74037, P77380H, 951-5003, 692-015, AFS0206P, RE0207P, 19111392, SP09A1H
Frequently Asked Questions
Does the Delphi HP10010 fit the 1990-1991 Chevrolet Lumina 4-cylinder 2.5L?
Yes. Delphi HP10010 fits the 1990-1991 Chevrolet Lumina 4-cylinder 2.5L, and that engine takes one hanger.
Does the Delphi fuel pump hanger assembly come with a float arm and O-rings?
Yes. Delphi HP10010 includes the float arm, a seal, a lock ring, two O-rings and an instruction sheet.
How does the float on this hanger affect the fuel gauge reading?
Its empty float height and float retention are held to specification, which helps the fuel gauge read correctly.
Can a worn hanger make the fuel gauge read wrong?
Yes, a float arm that no longer sits at the right height can throw the gauge off. Hard starting and stalling are other signs a hanger can show.
Do I need to clean the tank before installing this hanger?
Yes. Look the tank over and clean it before the new hanger is installed; the instruction sheet in the box gives the steps.
