Delphi TC2449 front right lower control arm with ball joint for the 2010-2025 Mercedes-Benz Sprinter 2500 and other vehicles connects the wheel to the chassis and gives it a pivot point at the ball joint. The ball joint comes as part of the arm, so one piece covers both.
- 100% crack detection and ultrasonic flaw detection on each control arm
- Ball studs machined to micron tolerances for durability and smooth joint operation
- Robot-welded control arm for consistent performance and quality
- Anti-corrosion protection applied to each part
- Tested at temperatures below -40 degrees C and over 120 degrees C
Quick facts
- Part: Delphi TC2449 control arm with ball joint
- Also called: control arm and ball joint assembly
- Fits: 2010-2025 Mercedes-Benz Sprinter 2500 and other vehicles
- Position: Front right lower
A worn arm or ball joint can show up as clunking over bumps, loose steering or uneven tire wear. Other suspension parts can produce similar symptoms, so find the cause before replacing anything; with the engine off, look at the arm from the wheel well for cracks, bends or rust. This listing is one arm for the front right; the front left is a separate part, and both sides are normally replaced together.
Fits
The 2010-2025 Mercedes-Benz Sprinter 2500, the 2010-2025 Mercedes-Benz Sprinter 3500 and the 2018-2025 Mercedes-Benz Sprinter 3500XD all fit this arm, and so do more vehicles; the front right position takes one. If your vehicle is not one of these, open the "Vehicles it fits" section to check its exact model and engine.
Specifications
Fit and size
- Position: front right lower
- Sold as: one arm for the front right
Build and materials
- Type: control arm with ball joint
- Construction: robot-welded arm, ball studs machined to micron tolerances
- Finish: anti-corrosion protection on each part
Interchange: 52-1626 · 2E0 407 152L · 2E0 407 152M · 906 330 41 07 · 906 330 47 07 · A906 330 41 07 · A 906 330 47 07
KSC5402 · CB81374 · CB81374PR · RK621967 · CMS101351 · CMS251134 · GS101351
This part cross-references / interchanges with the following part numbers:
52-1626, KSC5402, CB81374, CB81374PR, RK621967, 2E0 407 152L, 2E0 407 152M, 906 330 41 07, 906 330 47 07, A906 330 41 07, A 906 330 47 07, CMS101351, CMS251134, GS101351
Frequently Asked Questions
Does the Delphi TC2449 fit the 2018-2025 Mercedes-Benz Sprinter 3500XD?
Yes. Delphi TC2449 is listed for the 2018-2025 Mercedes-Benz Sprinter 3500XD as the front right lower control arm with ball joint.
Is this Delphi control arm and ball joint assembly for the left or right side?
It is the front right lower arm. The front left is a separate part, and this listing is one arm only.
How is the Delphi TC2449 protected against rust?
Anti-corrosion protection is applied to each Delphi TC2449, and Delphi parts are exposed to 720 hours of salt spray in testing.
Can a worn lower control arm cause clunking over bumps or uneven tire wear?
Yes, it can be one cause. A worn ball joint or arm can produce those signs, so have a shop check the joint and arm promptly rather than driving on.
Does the Delphi TC2449 replace part number 906 330 41 07?
Yes. 906 330 41 07 is one of the numbers Delphi TC2449 replaces, along with 2E0 407 152L and 2E0 407 152M.
