Delphi Suspension Stabilizer Bar Bushing Kit P/N:TD4045W
$16.99
(You save)
Take up the play in your front stabilizer bar and quiet the rattle it makes when the rubber wears out with the Delphi Suspension Stabilizer Bar Bushing Kit (TD4045W). This front-position stabilizer bar bushing kit drops in as a direct-fit replacement for the 1996-2002 Chevrolet Cavalier, 2004-2005 Chevrolet Classic, 1997-2003 Chevrolet Malibu, 1999-2003 Oldsmobile Alero, 1997-1999 Oldsmobile Cutlass, 1999-2003 Pontiac Grand Am and 1996-2002 Pontiac Sunfire. The bushings cushion the bar where it clamps to the chassis, letting it twist to limit body roll while isolating road noise — so if worn, split bushings are behind a clunk or rattle over bumps, these renew that contact point.
Designed to OE standards: built using Delphi's dimensional and material analysis for close compatibility between the OE and aftermarket part.
Validated to the extreme: tested below -40°C and above 120°C, plus 720 hours of salt-spray exposure.
Manufactured for consistent life and to reduce noise.
Helps restore the vehicle's smooth ride when tired bushings are the cause.
Delphi applies its OE safety expertise, fitted to millions of vehicles worldwide, across its aftermarket steering and suspension portfolio.
This part cross-references / interchanges with the following part numbers:
22600430, 22619843, K6651, MK6651, JBU1171
Frequently Asked Questions
What does this stabilizer bar bushing kit do?
The bushings cushion the front stabilizer bar where it mounts to the chassis, letting the bar twist to help limit body roll while isolating road noise at that contact point.
Which vehicles does the TD4045W fit?
It's a direct-fit replacement for the 1996-2002 Cavalier, 2004-2005 Classic, 1997-2003 Malibu, 1999-2003 Alero, 1997-1999 Cutlass, 1999-2003 Grand Am and 1996-2002 Sunfire. See the Buyer's Guide tab to confirm.
Is this a front or rear part?
It's cataloged for the front stabilizer bar position on the listed applications.
What are signs the stabilizer bar bushings need replacing?
Clunking, knocking or rattling over bumps and looser-feeling handling can point to cracked or worn bushings. Diagnose the cause first, since other suspension parts can produce similar symptoms.
How was this Delphi bushing kit tested?
Delphi validates it below -40°C and above 120°C and through 720 hours of salt-spray exposure, using dimensional and material analysis for close OE-to-aftermarket compatibility.
Write a Review
Delphi
Delphi Suspension Stabilizer Bar Bushing Kit P/N:TD4045W
Quiet a clunking, rattling front sway bar and help keep your Mercedes-Benz cornering flat with the Delphi Suspension Stabilizer Bar Bushing Kit TD5885W. This front-to-frame stabilizer bar bushing kit...
Quiet a clunking front sway bar and keep the stabilizer bar located where it belongs with the Delphi Suspension Stabilizer Bar Bushing Kit TD671W. These front stabilizer bar bushings cushion the bar...
Quiet a clunking front sway bar and keep the stabilizer bar properly located with the Delphi Suspension Stabilizer Bar Bushing Kit (TD994W). It drops in as a direct-fit replacement for the front...
Quiet a clunking rear sway bar and keep it precisely located with the Delphi Suspension Stabilizer Bar Bushing Kit (TD935W). This rear kit drops in for a wide range of BMW models, including the...
Quiet down clunks and steady the front sway bar with the Delphi Suspension Stabilizer Bar Bushing Kit TD5755W, a direct-fit replacement for the 2002-2006 Nissan Sentra. These front stabilizer bar...
WARNING:
These products can expose you to chemicals including lead and phthalates, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
