Delphi Suspension Stabilizer Bar Bushing Kit P/N:TD4098W
$18.99
(You save)
Quiet a clunking, rattling sway bar and keep the stabilizer bar located where it belongs with the Delphi Suspension Stabilizer Bar Bushing Kit (TD4098W). This kit mounts front to frame and rear to axle and drops in as a direct-fit replacement for the 2007-2011 Ford Mustang, 1986-1999 Ford Taurus, 1995-2003 Ford Windstar, 1988-2002 Lincoln Continental and 1986-1999 Mercury Sable — see the Buyer's Guide tab for engine-level details.
Designed to OE standards: Delphi applies its OE steering-and-suspension expertise to the aftermarket, with extensive dimensional and material analysis for close compatibility between the OE and the replacement bushings.
Tested to the extreme: validated below -40°C and above 120°C and exposed to 720 hours of salt spray for OE-level performance.
Built for consistent life: manufactured to deliver consistent service and to reduce noise.
Smoother ride: designed to help restore the vehicle's smooth ride when worn bushings are the cause of the noise or looseness.
Worn or cracked sway bar bushings can show up as clunking or rattling over bumps and a loose-feeling stabilizer bar; if the bushings are the cause, this kit replaces them.
It's a Delphi sway bar bushing kit (also called a stabilizer bar bushing kit) that replaces the rubber bushings which locate and isolate the stabilizer bar, mounting front to frame and rear to axle.
Which vehicles does it fit?
It's a direct-fit replacement for the 2007-2011 Ford Mustang, 1986-1999 Ford Taurus, 1995-2003 Ford Windstar, 1988-2002 Lincoln Continental and 1986-1999 Mercury Sable. Check the Buyer's Guide tab for engine-level details.
What are signs my sway bar bushings need replacing?
Clunking or rattling over bumps and a loose or vague-feeling stabilizer bar can be signs of worn or cracked bushings. Diagnose the cause first; if the bushings are at fault, this kit replaces them.
Are these bushings built to withstand harsh conditions?
Delphi validates its parts below -40°C and above 120°C and exposes them to 720 hours of salt spray, and the bushings are designed to OE standards for consistent service.
What numbers does this kit interchange with?
It cross-references 602.65128, E6DZ-5493B, 928303, K8794, K8802, GK8802, MK8802 and JBU1169.
Write a Review
Delphi
Delphi Suspension Stabilizer Bar Bushing Kit P/N:TD4098W
Quiet a noisy rear stabilizer bar and keep it properly located with the Delphi Suspension Stabilizer Bar Bushing Kit TD1455W. This rear sway bar bushing kit drops in as a direct-fit replacement for...
Quiet front-end rattle and keep the stabilizer bar firmly located to the control arm with the Delphi Suspension Stabilizer Bar Bushing Kit TD4128W. These front-to-control-arm bushings cushion and...
Quiet the clunk and rattle from a loose stabilizer bar and hold it firmly to the chassis with the Delphi Suspension Stabilizer Bar Bushing Kit TD4074W. This front-to-frame stabilizer bar bushing kit...
Quiet down front-end rattle and keep your stabilizer bar located where it belongs with the Delphi Suspension Stabilizer Bar Bushing Kit TD4053W. This front sway bar bushing kit installs as a...
Keep the front stabilizer bar firmly located and help quiet suspension rattle with the Delphi Suspension Stabilizer Bar Bushing Kit (TD4566W). This front sway bar bushing kit installs as a direct-fit...
WARNING:
These products can expose you to chemicals including lead and phthalates, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
