Delphi Suspension Stabilizer Bar Bushing Kit P/N:TD4186W
$11.99
(You save)
Quiet a rattling front stabilizer bar and keep it located through every turn with the Delphi Suspension Stabilizer Bar Bushing Kit (TD4186W). This front sway bar bushing kit drops in as a direct-fit replacement for the 2005-2013 Chrysler 300, 2008-2013 Dodge Challenger, 2006-2013 Dodge Charger, and 2005-2008 Dodge Magnum — see the Buyer's Guide tab for engine-level fitment.
The bushings cushion the front stabilizer bar where it mounts to the chassis, helping the bar resist body roll while isolating road noise and vibration. Cracked, worn, or hardened bushings are a common source of front-end clunks and rattles over uneven pavement; if the bushings are the cause, this kit replaces them.
Built to OE standards: Delphi bushings are designed to OE standards, drawing on Delphi's OE steering and suspension expertise.
Consistent service life: manufactured for consistent life so the fit stays predictable.
Noise reduction: manufactured to reduce noise and assist in restoring the vehicle's smooth ride.
Validated durability: Delphi tests to the extreme — parts withstand below -40°C and over 120°C and endure 720 hours of salt spray, backed by extensive dimensional and material analysis for OE-to-aftermarket compatibility.
What is a stabilizer bar bushing kit and what does it do?
It supplies the bushings that cushion and locate the front stabilizer bar where it mounts to the chassis, helping the bar control body roll while isolating road noise and vibration.
Which vehicles does the Delphi TD4186W fit?
It's a direct-fit replacement for the 2005-2013 Chrysler 300, 2008-2013 Dodge Challenger, 2006-2013 Dodge Charger, and 2005-2008 Dodge Magnum. Check the Buyer's Guide tab for engine-level fitment.
What are signs my sway bar bushings may need replacing?
Clunking, rattling, or knocking from the front end over bumps and uneven roads, along with cracked or hardened bushings. Diagnose the cause first, since other suspension parts can produce similar noises.
Is this a front or rear part?
This kit is cataloged for the FRONT stabilizer bar position on the listed applications.
How were these Delphi bushings tested?
Delphi validates them to OE standards with extensive dimensional and material analysis, exposure below -40°C and over 120°C, and 720 hours of salt spray.
Write a Review
Delphi
Delphi Suspension Stabilizer Bar Bushing Kit P/N:TD4186W
Quiet a clunking rear sway bar and keep it located under hard cornering with the Delphi Suspension Stabilizer Bar Bushing Kit (P/N: TD4177W). This kit cushions the rear stabilizer bar where it mounts...
Keep the rear stabilizer bar located and quiet with the Delphi Suspension Stabilizer Bar Bushing Kit (TD5070W). These bushings secure the rear stabilizer bar to the frame, cushioning it against the...
Quiet a clunking, knocking rear sway bar and keep the stabilizer bar located properly with the Delphi Suspension Stabilizer Bar Bushing Kit (TD996W). This rear sway bar bushing kit cushions the bar...
Quiet a clunking, rattling front sway bar and help keep your Mercedes-Benz cornering flat with the Delphi Suspension Stabilizer Bar Bushing Kit TD5885W. This front-to-frame stabilizer bar bushing kit...
Quiet a clunking front sway bar and keep the stabilizer bar located where it belongs with the Delphi Suspension Stabilizer Bar Bushing Kit TD671W. These front stabilizer bar bushings cushion the bar...
WARNING:
These products can expose you to chemicals including lead and phthalates, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
