Delphi Suspension Stabilizer Bar Link Kit P/N:TC3228
$28.99
(You save)
Tie the front stabilizer bar to the suspension and keep body roll in check with the Delphi Suspension Stabilizer Bar Link Kit TC3228. This FRONT LEFT sway bar link is a direct-fit replacement for the 2009-2014 and 2016-2021 Nissan Maxima, 2013-2022 Nissan Altima, 2013-2020 Nissan Pathfinder, 2015-2021 Nissan Murano, 2013 Infiniti JX35 and 2014-2019 Infiniti QX60 — see the Buyer's Guide tab for engine-level fitment. A worn stabilizer link often shows up as a knocking or rattling noise over bumps and a vague, roll-prone feel through corners; if a failed link is the cause, this kit replaces it.
Fatigue tested: Delphi sway bar links are fatigue tested to help avoid failure.
Ultrasonic molding: built with ultrasonic molding to help guard against future weld breakage.
Micron tolerances: machined to micron tolerances for durability and smooth joint operation.
Anti-corrosion protection: applied to each part for corrosion prevention and improved appearance.
This stabilizer bar link kit is engineered against Delphi's OE expertise, with dimensional and material analysis for close OE-to-aftermarket compatibility.
What is a stabilizer bar link kit and what does it do?
It connects the stabilizer (sway) bar to the suspension, helping control body roll during cornering. TC3228 is the FRONT LEFT link for the listed vehicles.
Which vehicles does the Delphi TC3228 fit?
It fits the 2013-2022 Nissan Altima, 2009-2014 and 2016-2021 Nissan Maxima, 2013-2020 Pathfinder, 2015-2021 Murano, 2013 Infiniti JX35 and 2014-2019 QX60. See the Buyer's Guide tab.
What position is this link?
This is the FRONT LEFT stabilizer bar link. Confirm the position needed for your vehicle before ordering.
What are common signs this part may need replacing?
Knocking or rattling over bumps and a vague, roll-prone feel in corners can be signs of a worn link. Have the cause diagnosed, as other parts can produce similar symptoms.
How is the Delphi link built for durability?
It is fatigue tested, built with ultrasonic molding to help prevent future weld breakage, machined to micron tolerances, and treated with anti-corrosion protection.
Write a Review
Delphi
Delphi Suspension Stabilizer Bar Link Kit P/N:TC3228
Keep body lean in check and quiet the clunks with the Delphi Rear Suspension Stabilizer Bar Link Kit (TC2616) — a direct-fit replacement for the 2002-2007 Mitsubishi Lancer (see the Buyer's Guide tab...
Tighten up front-end response and quiet the clunks with the Delphi Suspension Stabilizer Bar Link Kit TC6165. These front sway bar links connect the stabilizer bar to the suspension, transferring...
Quiet the clunks and keep the rear stabilizer bar tied to the suspension with the Delphi Suspension Stabilizer Bar Link Kit TC6526. This rear-position stabilizer bar link kit drops in as a direct-fit...
Keep body roll in check and quiet the rattles with the Delphi Front Suspension Stabilizer Bar Link Kit TC6540. This front sway bar link connects the stabilizer bar to the suspension so the bar can...
Tie the front stabilizer bar to the suspension and help control body roll through every corner with the Delphi Suspension Stabilizer Bar Link Kit (TC2265). This front sway bar link kit is a...
WARNING:
These products can expose you to chemicals including lead and phthalates, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
