Dorman 522-568 front right lower control arm with ball joint for the 2014-2024 Infiniti Q50 and other vehicles connects the steering knuckle to the chassis. This control arm and ball joint assembly comes with the ball joint and bushings pre-installed, which saves time and labor.
- Dorman OE Solutions line, standard replacement grade
- Threaded ball joint stud with a 16 mm thread diameter
- Aluminum control arm with rubber bushings
- Additional coatings for rust and corrosion resistance
- Evaluated for a smooth ride, directional stability and predictable dynamics
Quick facts
- Part: Dorman 522-568 control arm with ball joint
- Also called: control arm and ball joint assembly
- Fits: 2014-2024 Infiniti Q50 and other vehicles
- Position: Front right lower
- Material: Aluminum control arm, rubber bushings
- Condition: New
A clunk over bumps, vague steering or uneven tire wear can mean a worn bushing or ball joint. Before replacing the arm, look over the rubber bushings and ball joint where you can see them, with the engine off, for cracks or tears. A shop can check ball joint play, since that needs the car raised, and the same noises can come from other suspension parts.
Fits
The vehicles it fits include the 2014-2024 Infiniti Q50, the 2014-2022 Infiniti Q60 and the 2009-2021 Nissan 370Z, and it is a direct replacement for the original equipment on these applications. If your car is not named here, look it up in the "Vehicles it fits" section. This listing is one arm for the front right; the front left is a separate part, and the two are normally replaced together.
Specifications
Fit and size
- Position: front right lower
- Quantity per vehicle: 1 for this side
- Control arm maximum length: 460 mm
- Control arm maximum width: 390 mm
- Mounting hole diameter: 14.2 mm, 3 mounting holes
- Ball joint thread diameter: 16 mm
Build and materials
- Control arm type: Casting/Forged
- Control arm material: aluminum
- Bushing material: rubber
- Ball joint stud: threaded, installed
- Adjustable: no
- Condition: new
- Country of origin: Thailand
In the box
One control arm with the ball joint and bushings installed, and one nut. The front right side takes one arm. A grease fitting is not included.
Interchange: 102-7731
TC8784 · CA14810 · 9CB30324 · RK623471 · GS301112 · CMS301112 · 2606803 · 545001BD1A · 545001BD1B · 545001BD2B · 54500JL00C · 54500JL01A · 54500JL01B · 54500JL02B · 54500JL03B · 54500JL04B · 54500JU50A
This part cross-references / interchanges with the following part numbers:
102-7731, TC8784, CA14810, 9CB30324, RK623471, GS301112, CMS301112, 2606803, 545001BD1A, 545001BD1B, 545001BD2B, 54500JL00C, 54500JL01A, 54500JL01B, 54500JL02B, 54500JL03B, 54500JL04B, 54500JU50A
Frequently Asked Questions
Does the Dorman 522-568 control arm fit the 2014-2022 Infiniti Q60?
Yes. Dorman 522-568 is a front right lower arm for the 2014-2022 Infiniti Q60, and no engine restriction applies.
Does this front right control arm come with the ball joint and bushings installed?
Yes. Dorman 522-568 comes with the ball joint and rubber bushings pre-installed, plus one nut; a grease fitting is not included.
Is this lower control arm made of aluminum or steel?
Aluminum. The control arm is a casting/forged type in aluminum, and its bushings are rubber.
How can I tell if the bushings or ball joint on my lower control arm are worn?
Cracked or torn rubber you can see, a clunk over bumps or uneven tire wear can point to wear. A shop can test ball joint play, which needs the car raised.
Is 54500JL00C an interchange number for Dorman 522-568?
Yes. 54500JL00C is one of the numbers Dorman 522-568 replaces, along with 545001BD1A and 54500JU50A.
