Delphi Suspension Control Arm and Ball Joint Assembly P/N:TC6263
$79.99
(You save)
Firm up the front end with the Delphi control arm — the Suspension Control Arm and Ball Joint Assembly, MPN TC6263. This front right upper unit installs as a direct-fit replacement for GM full-size trucks and SUVs, so whether you're replacing a worn K1500 control arm or a Tahoe control arm, the ball joint arrives pre-installed for a single, straightforward job.
Delphi applies its OE steering expertise to its aftermarket line:
Validated to extremes: tested from below -40°C to over 120°C and through 720 hours of salt spray, with dimensional and material analysis matching the OE and aftermarket part.
Inspected 100%: crack detection and ultrasonic flaw detection confirm the materials match OE specifications.
Precision ball studs: machined to micron tolerances for durability and smooth joint operation.
Built to hold up: robot-welded for consistent quality, with anti-corrosion protection applied to each part for corrosion prevention and enhanced aesthetics.
Fits: 1988-1999 Chevrolet K1500 · 1988-2000 Chevrolet K2500 · 1988-1999 GMC K1500 · 1988-2000 GMC K2500 · 1990-2005 Chevrolet Astro · 1990-2005 GMC Safari · 1992-1999 Chevrolet K1500 Suburban · 1992-1996 Chevrolet K2500 Suburban · 1992-1999 GMC K1500 Suburban · 1992-1996 GMC K2500 Suburban · 1992-2000 GMC Yukon · 1995-2000 Chevrolet Tahoe · 1999-2000 Cadillac Escalade. See the Buyer's Guide tab to confirm your vehicle.
The ball joint comes pre-installed on the control arm as one unit, so you replace both together in a single install. It's the front right upper part, MPN TC6263.
Is this the right chevy Tahoe control arm for me?
It fits the 1995-2000 Chevrolet Tahoe in the front right upper position. Check the Buyer's Guide tab to confirm your exact vehicle before ordering.
Is this also a Gmc Yukon control arm?
Yes — it's listed as the front right upper unit for the 1992-2000 GMC Yukon, along with GM K1500/K2500 trucks, Astro, Safari and Escalade.
What are the signs this part may need replacing?
Clunking or knocking over bumps, loose or wandering steering, and uneven front tire wear can point to a worn control arm or ball joint. Diagnose the cause before replacing.
How is this part protected against corrosion?
Delphi applies anti-corrosion protection to each part for corrosion prevention and improved appearance, and the design is validated through 720 hours of salt spray testing.
Write a Review
Delphi
Delphi Suspension Control Arm and Ball Joint Assembly P/N:TC6263
Suspension Control Arm and Ball Joint AssemblyDelphi's OE safety technology is fitted to millions of vehicles worldwide and we apply Delphi's OE expertise to our aftermarket steering portfolio...
Suspension Control Arm and Ball Joint AssemblyDelphi's OE safety technology is fitted to millions of vehicles worldwide and we apply Delphi's OE expertise to our aftermarket steering portfolio...
Suspension Control Arm and Ball Joint AssemblyDelphi's OE safety technology is fitted to millions of vehicles worldwide and we apply Delphi's OE expertise to our aftermarket steering portfolio...
Suspension Control Arm and Ball Joint AssemblyDelphi's OE safety technology is fitted to millions of vehicles worldwide and we apply Delphi's OE expertise to our aftermarket steering portfolio...
WARNING:
These products can expose you to chemicals including lead and phthalates, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
