Delphi Suspension Stabilizer Bar Bushing Kit P/N:TD1213W
$10.99
(You save)
Quiet a clunking front sway bar and keep it located under hard cornering with the Delphi Suspension Stabilizer Bar Bushing Kit TD1213W. This front-position bushing kit is a direct-fit replacement for the 1995 BMW 320I, 1995 BMW 325I, 1995 BMW 325IS, 1996-1999 BMW 328I, 1996-1999 BMW 328IS, 1997-2000 BMW Z3, 1998-1999 BMW 323I and 1998-1999 BMW 323IS — see the Buyer's Guide tab for engine-level details.
Designed to OE standards: Delphi applies its OE steering and suspension expertise to this aftermarket bushing kit for close compatibility with the original part.
Validated to the extreme: Delphi parts are exposed to temperatures below -40°C and above 120°C plus 720 hours of salt spray, with extensive dimensional and material analysis.
Built for consistent life and reduced noise: the bushings are manufactured for a consistent service life and to help keep sway-bar noise down.
Helps restore ride quality: fresh bushings assist in restoring the vehicle's smooth ride when worn originals are the cause of front-end clunk.
This stabilizer bar bushing kit cushions the front sway bar in its brackets so it can control body roll while limiting metal-to-metal contact. If worn, dry, or cracked bushings are behind your front-end clunk over bumps or during cornering, this kit replaces them.
What is a stabilizer bar bushing kit and what does it do?
It's a set of bushings that cushion the front sway bar in its mounting brackets, letting the bar control body roll while limiting metal-to-metal contact and noise.
Does the Delphi TD1213W fit my BMW?
It's a direct-fit front kit for the 1995 320I/325I/325IS, 1996-1999 328I/328IS, 1997-2000 Z3, and 1998-1999 323I/323IS. Check the Buyer's Guide tab to confirm your vehicle.
Is this a front or rear kit?
This kit is cataloged for the FRONT sway bar position on the listed BMW applications.
What are the signs my sway bar bushings need replacing?
Common signs include a clunk or rattle from the front over bumps or during cornering, or cracked and worn bushings. Diagnose the cause before replacing, as other parts can make similar noises.
How is Delphi's quality validated?
Delphi tests parts below -40°C and above 120°C, exposes them to 720 hours of salt spray, and performs extensive dimensional and material analysis for OE-level compatibility.
Write a Review
Delphi
Delphi Suspension Stabilizer Bar Bushing Kit P/N:TD1213W
Quiet a clunking, rattling front sway bar and help keep your Mercedes-Benz cornering flat with the Delphi Suspension Stabilizer Bar Bushing Kit TD5885W. This front-to-frame stabilizer bar bushing kit...
Quiet a clunking front sway bar and keep the stabilizer bar located where it belongs with the Delphi Suspension Stabilizer Bar Bushing Kit TD671W. These front stabilizer bar bushings cushion the bar...
Quiet a clunking front sway bar and keep the stabilizer bar properly located with the Delphi Suspension Stabilizer Bar Bushing Kit (TD994W). It drops in as a direct-fit replacement for the front...
Quiet a clunking rear sway bar and keep it precisely located with the Delphi Suspension Stabilizer Bar Bushing Kit (TD935W). This rear kit drops in for a wide range of BMW models, including the...
Quiet a clunking, knocking rear sway bar and keep the stabilizer bar located properly with the Delphi Suspension Stabilizer Bar Bushing Kit (TD996W). This rear sway bar bushing kit cushions the bar...
WARNING:
These products can expose you to chemicals including lead and phthalates, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
